A jet of water discharges into a 90-cm open cylindrical tank with a height of 1 m. The cross-sectional area of the jet is 0.0025 m2 where the velocity of water jet is 3 m/s. How many seconds is required to fully fill the tank? The following are given for the measurements of a 90-cm open cylindrical tank when a jet of water discharges. height= 1m velocity=3m/s Area=0.0025m2 Determine the time to fully fill the cylindrical tank.

A jet of water discharges into a 90-cm open cylindrical tank with a height of 1 m. The cross-sectional area of the jet is 0.0025 m2 where the velocity of water jet is 3 m/s. How many seconds is required to fully fill the tank? The following are given for the measurements of a 90-cm open cylindrical tank when a jet of water discharges. height= 1m velocity=3m/s Area=0.0025m2 Determine the time to fully fill the cylindrical tank.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 45P

See similar textbooks

Similar questions

A tank is in the shape of an inverted cone, having height h = 2.5 m and base radius r = 0.75 m. If water is poured into the tank at a rate of 15 L/s, how long will it take to fill the tank? Water flows into a cubical tank at a rate of 15 L/s. If the top surface of the water in the tank is rising by 1.5 cm every second, what is the length of each side of the tank?
Water enters a large rigid tank steadily at a rate of V . = 0.5 m3/s, and exits through a large rectangular opening through which the velocity changes linearly in the vertical direction from 4 m/s to 5 m/s. Knowing that the tank is full, determine the magnitude of the velocity through the circular opening at the top whose diameter is D = 15 cm.
An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1.6m. It is rotated about its vertical axis at 13 rad/s. How many liters of water are spilled? Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
Air is introduced through a nozzle into a tank of water to form a stream of bubbles. If the bubbles are intended to have a diameter of 2mm, calculate by how much the pressure of the air at the nozzle must exceed that of the surrounding water. Assume that surface tension of water is 0.073 N/m. What would be the absolute pressure inside the bubble if the surrounding water is at 100 kPa?
1.) Water flows at 10m3/s in a 150-cm diameter pipe; the head loss in a 1000-m length of this pipe is 20.0m. Find the rate of energy loss due to pipe friction for the pipe. Use unit weight of Water : 9.79KN/m3.2.) Given the two dimensional flow as shown in the accompanying figure. Determine the flow rate considering 1.5m of width perpendicular to the figure.
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the time in seconds to lower the head from 1.20 m to 0.80 m?
A supply of water to reservoir C is drawn from two open reservoirs A and B by pipe network shown in the figure below. The elevation of water in both A and B is 10 m above the level in C. The friction factor may be assumed to be a constant with a value of 0.02. If the valve on the pipe from reservoir B is initially closed, determine the rate of flow from reservoir A, in m choices 0.00416 0.00306 0.01008 0.00702 PIPE AB BD CD LENGTH (m) 100 200 300 DIAMETER (mm) 50 80 100
A hollow cylinder 1.55m in diameter and 7m long weighs 3,055N. How many cubic meters of metal weighing 105 kN/m3 must be placed inside the cylinder such that 2.6m of the cylinder is protruding above the liquid surface? The hollow cylinder is submerged in a liquid that has a specific gravity of 2.8.
A cylindrical tank having a diameter of 3.5m and a height of 10m is full of water. there is an orifice at the bottom of the tank having an area of 0.025 m^2. if the tank has a coefficient of discharge of 0.60, how long will it take to empty the tank in minutes?
Shown in the figure below is a small decorative wheel fitted with flat paddles so the wheel turns about its axis when acted upon by a blown stream of air. Assuming that all the air in a 15-mm-diameter stream moving at 0.35 m/s strikes one paddle and is deflected by it at right angles, compute the force exerted on the wheel initially when it is stationary. The air has a density of 1.20 kg/m3 . The paddle is on a horizontal plane.
A hemispherical tank having a radius of 2.5 m is filled with water to a depth of 1.8 m. If a solid sphere having a diameter of 1.6 m is placed on the bowl, determine how high will the water rise on the bowl. A. 176 mm B. 166 mm C. 171 mm D. 116 mm
An orifice with 0.80 cm radius is inserted in a vertical wall of a tank under a constant head of 5.70 m discharges 0.45 m3 in 9.50 minutes. Find the coefficient of discharge.