A cylindrical vessel made of stainless steel has a diameter of 20 m and a thickness of 12 mm had used for natural gas storage. It was recommended that the working stress of this material is 300 MPa. Determine the allowable gas pressure.

Q: An inert gas held in a plunger undergoes three stages: Stage 1-2: the gas is compressed without any…

A:

Q: A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. The…

A: Given:t=20 mm = 20×10-3 mL=3 mD=500 mm = 0.5 mStress in steel is given by,σlong=PD4t

Q: The valve between a 9L tank containing gas at 5 atm and a 6 L tank containing gas at 10 atm is…

A:

Q: Is the adiabatic expansion of superheated steam from 850°C and 2.0 MPa to 650°C and 1.2 MPa…

A:

Q: A steam boiler of volume 2.3 m3 initially contained 1.7 m3 liquid water in equilibrium with 0.6 m3…

A:

Q: [Q51 (a) The chamber contains 0.05 m' of ideal gas at a pressure of 20 KPa. The gas is subjected to…

A:

Q: Is there any chance of having an oil/gas reservoir in your place? Justify your answer

A: No its not safe to store oil reservoir at our place, it needs special tanks and safety measures to…

Q: For a process with an ideal gas assuming constant specific heats, which set of values should be used…

A: Internal energy is the energy of a substance that changes with the change in the temperature of the…

Q: What do you mean by specific heat at constant pressure?

A: The process of heat transfer to a gas system can occur or can be done in different ways such as: At…

Q: A drum 6 inches in diameter and 40 inches long contained acetylene at 250 psia and 80 degrees…

A:

Q: how did you convert the atm pressure mm Hg?

A: 1 atm = 101.325 kPa = 760 mm of Hg = 10.3 m of water

Q: Q 5 A vertical axis circular cylindrical water storage tank of cross-sectional area A is filled to a…

A:

Q: 079-For the system shown in fig the work done is, b- -300 kJ, c- -400 kJ, a-300 kJ, d- 450 kJ

A:

Q: In a reheat cycle steam at 550°C expands in an turbine till it is saturated vapor. It is reheated at…

A: The reheat cycle is a cycle for the device used to generate energy using heat in the form of fluid.…

Q: What does the Hooke’s law involve?

A: The Hook’s law involves the relationship between the strain due to external load and the stress…

Q: Define the combination u + Pv is often encountered in the analysis of control volumes.

A: The term u+Pv encountered in the analysis of the control volume is known as the enthalpy. It is the…

Q: PROBLEM 1 A 10 m³ rigid tank contains R-134a at 200 kPa and 20°C. Heat is added to the tank until…

A: The isochoric process is a thermodynamic process that takes place at a constant volume. It's also…

Q: Q4:0 5kg of Steam at pressure of 4.9 bar is produ- ced from water at 20% . Determine the amount of…

A:

Q: Obtain the expression of the critical pressure in terms of Van der Waals constants for real gases.

A:

Q: Ssure of the tank if the 8. An acetylene tank consists of a cylindrical body flat at its base and a…

A: Dear student, as per the given data there is no correct option. Please find the attached solution.

Q: When does the Hooke's Law apply?

A: Hooke's Law establishes the linear relationship between stress and strain. But it limits this…

Q: Two spheres each 3.0ft in diameter are connected by a pipe in which there is a valve. Each sphere…

A:

Q: The angle embraced is 175° and the coefficient of friction between the belt and the pulley is 0.25.…

A:

Q: Represent these processes on a pressure-volume (p-V) diagram.

A: We are going to draw the P-V diagram

Q: 27. A particular balloon is designed by its manufacturer to be inflated to a volume of no more than…

A: Ideal gas equation PV=nRT is used for both the conditions with same number of moles.

Q: The instruction booklet for your pressure cooker indicates that its highest setting is 11.3 psipsi .…

A:

Q: A piston cylinder arrangement initially contains 7.0 kg of super-heated steam at 100 kPa and 250 C,…

A:

Q: A cylindrical pressure vessel has an inner diameter of 5 ft and a thickness of 3/4 in. The stress…

A:

Q: 1.5 kg ethane gas was filled in a tube with a volume of 12 dm3. It was heated by a bottom heating…

A: Calculating the final temperature with the means of Ideal Gas Equation viz., PV=nRT n=no.of moles…

Q: The gas tank is made from A-36 steel (σYield= 440 MPa) and has an inner diameter of 1.5 m and a wall…

A:

Q: A 6 ft-long steam pipe is made of A-36 steel with allowable stress of 40 ksi. It is connected…

A: Given data: σ=40 ksido=4 indi=4-2×0.25=3.5 inT2=275°FT1=70°F Need to determine the force exert in…

Q: Demonstrate if this compression of gas is isentropic.

A: Given Data The initial temperature is:Ti=20°C The volume flow rate is:V˙=120litres/minute=120×10-3…

Q: An ideal gas at 43 psig and 82°F is heated in a rigid tank to 120°F. Determine the final pressure in…

A:

Q: How would you suggest that he loses this energy? Explain your answer clearly and convincingly.

A:

Q: A rigid tank with a volume of 0.12355 m³ contains 1 kg of refrigerant-134a vapor at 240 kPa. The…

A:

Q: Question Solution & Answer 1. A l-m' rigid tank contains 10 kg of water (in any phase or phases) At…

A: 1. Given, mass, m=10kgvolume, V=1m3Temperature, T=160°C=433KTo calculate :- PressureFrom the gas…

Q: A heat engine using 120mg of helium as the working substance follows the cycle shown in the…

A: Givenm=120mg=0.120g=0.120×10-3 kg

Q: The tank is now heated to 110 "C Use the compressed liquid table to determine the pressure in the…

A:

Q: Consider a quantity of 2.0 kg of refrigerant R-134a. The refrigerant fills a 9.9 ft weighted…

A:

Q: During processing in a steel mill, a 900 lb steel casting at 800°F is quenched by plunging it into a…

A:

Q: This is the second part of a two-part problem. The piston/cylinder in the figure contains 0.5 kg of…

A: As per question, At initial condition, mass, m=0.5kgPressure,P1=250KpaSpecific internal energy,…

Q: Spherical pressure vessel: 02 %3D 2t A pressurized spherical tank is made of 25 mm thick steel. If…

A:

Q: 13-7. A boiler is constructed of 8-mm-thick steel plates that are fastened together at their ends…

A: Given data P=1.35 MPar=0.75 mmt=8 mm

Q: A frictionless piston is used to provide a constant pressure of 500 kPa in a cylinder containing…

A:

Q: V1 = 176 m-s1,T, = 25 °C, p, = 298 kPa, (Design condition), Ae = 0.014 m?, pb = 110 kPa, determine…

A: Given that, Ae=0.014 m2Pb=110 kPa,P1=298 kPa,T1=25 °C,v1=176 m/sec,   Calculate the velocity of…

Q: Q1-A wet gas has composition as given below. Determine a value of z-factor for this gas at reservoir…

A: