The angle embraced is 175° and the coefficient of friction between the belt and the pulley is 0.25. A leather belt is required to transmit 9.5 kW from a pulley 10 cm in diameter, running at 200 r.p.m.. If the safe working stress for the leather belt is 2 MPa, density of leather 1000 Kg/m and thickness of belt 1 cm, determine the width of the belt taking centrifugal tension into account.

The angle embraced is 175° and the coefficient of friction between the belt and the pulley is 0.25. A leather belt is required to transmit 9.5 kW from a pulley 10 cm in diameter, running at 200 r.p.m.. If the safe working stress for the leather belt is 2 MPa, density of leather 1000 Kg/m and thickness of belt 1 cm, determine the width of the belt taking centrifugal tension into account.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An open belt running over two pulleys 24 em and 60 cm diameters connects two parallel shafts 3 m apart and transmits 3.75 KW from the smaller pulley that rotates at 300 r.p.m. coefficient of friction between the belt and the pulleys is 0.3 and the safe working tension is 100 N/em width. Determine: i) minimum width of the belt, ii) initial belt tension, and i) length of the belt required.
.A belt 200 mm wide and 7 mm thick drives a pulley at belt speed of 25 m/s. The density of the belt is 980 kg/m3 and the coefficient of friction between the belt and pulley is 0.23. Given that the angle of contact of pulley is 2π/3 and the allowable stress of the belt is 1.8 MPa, determine the tension on the slack side of the belt (T2) in N
A mass of 4.0 kg is placed on a spring which has a spring constant of 256 N/m and compresses it a length of 87 cm from its equilibrium position. This set up is on an incline at an angle of 40º above the horizontal and there is a coefficient of kinetic friction of 0.17 between the mass and the surface. What will the speed of the mass be when it has moved a total distance of 1.0 m up the incline from its starting position. (Use g = 9.8m/s2 and round answer to 1 decimal place.)
An 80-percent-efficient pump with a power input of 20 hp is pumping water from a lake to a nearby pool at a rate of 1.5 ft3 /s through a constant-diameter pipe. The free surface of the pool is 80 ft above that of the lake. Determine the mechanical power used to overcome frictional effects in piping.
A 50 kg box is pushed up an inclined plane at a constant speed. The coefficient of friction between the box and the plane is 0.4. Determine the efficiency of the plane which is 6 meters long and angled at 40owith the horizontal.
Problem 8The demand for electric power is usually much higher during the day than it is at night, andutility companies often sell power at night at much lower prices to encourage consumers to usethe available power generation capacity and to avoid building new expensive power plants thatwill be used only a short time during peak periods. Utilities are also willing to purchase powerproduced during the day from private parties at a high price. Suppose a utility company is selling electric power for $0.07/kWh at night and is willing to pay $0.15/kWh for power produced during the day. To take advantage of this opportunity, an entrepreneur is considering building a large reservoir 100 m above the lake level, pumping water from the lake to the reservoir at night using cheap power, and letting the water flow from the reservoir back to the lake during the day, producing power as the pump–motor operates as a turbine–generator during reverse flow. Preliminary analysis shows that a water flow…
Work done by the frictional force depends on which factors?
Work done by the spring force depends on which factors?
A block P of weight 50 N is kept on a plane and now pulled so that the extension in the spring is 10 cm. The stiffness of the spring is 4 N/cm and the coefficient of friction between the block and the plane is μ = 0.3. Find (i) the velocity of the block as the spring returns to its undeformed state and (ii) the maximum compression in the spring. ( By principle of conservation) ( answer= maximum compression is 2.5cm) ( explain with proper steps)
The elevator of a large building is to raise a net mass of 550 kg at a constant speed of 12 m/s using an electric motor. The minimum power rating of the motor should be (a) 0 kW (b) 4.8 kW (c) 12 kW (d) 45 kW (e) 65 kW
An engine cylinder is 127mm in diameter, and the piston stroke is 508mm long, the clearance volume is 0.001m3, and the pressure constant is 735kPa. What is the work done in the cylinder during a single stroke? A) 3.995 kJ B) 2.530 kJ C) 8.576 kJ D) 5.287 kJ
A heat machine receives heat from a high-temperature heat source at a temperature of 160 °C andIt delivers heat to a high-temperature heat source at a temperature of 5 °C. In the meantime jobit is claimed that 0.15 kWh of work is done per every 1000 KJ of heat that the machine receivesare made. 1 if the claim is true. and 2. Evaluate according to the law.