A 6 ft-long steam pipe is made of A-36 steel with allowable stress of 40 ksi. It is connected directly to two turbines as shown. The pipe has an outer diameter of 4 in and a wall thickness of 0.25 in. The connection was made at an initial temperature of 70°F. If the turbines' points of attachment are assumed rigid, determine the force the pipe exerts on the turbines when the steam and thus the pipe reach a final temperature of 275°F. Use the coefficient of linear expansion for steel.

A 6 ft-long steam pipe is made of A-36 steel with allowable stress of 40 ksi. It is connected directly to two turbines as shown. The pipe has an outer diameter of 4 in and a wall thickness of 0.25 in. The connection was made at an initial temperature of 70°F. If the turbines' points of attachment are assumed rigid, determine the force the pipe exerts on the turbines when the steam and thus the pipe reach a final temperature of 275°F. Use the coefficient of linear expansion for steel.

Name: A 6 ft-long steam pipe is made of A-36 steel with allowablestress of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 6 ft-long steam pipe is made of A-36 steel with allowablestress of 40 ksi. It is connected directly to two turbinesas shown. The pipe has an outer diameter of 4 in and a wallthickness of 0.25 in. The connection was made at an initialtemperature of

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The gas tank consists of a cylindrical section with two hemispherical endcaps. The cylinder has a diameter of 75 cm and a wall thickness of 2 cm. If the allowable circumferential stress is 150 MPa and longitudinal stress is 100 MPa, find the maximum allowable internal pressure in the tank. Answer: P = ___________________
The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.
Q2/ How much fluid is required to raise the pressure in a thin cylinder of length 3 m, internal diameter 0.7 m, and wall thickness 12mm by 70kN/m*? E = 210GN/m* and v = 0.3 for the material of the cylinder and K = 2.1 GN/m* for the fluid.
What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
The spherical gas tank is fabricated by bolting together two hemispherical thin shells. If the 510 cm inner diameter tank is to be designed to withstand a gauge pressure of 2802 kPa, determine the minimum number of 28-mm diameter bolts that must be used to seal it. The tank and the bolts are made from material having an allowable normal stress of 130 GPa and 323 MPa,respectively.
A fish tank that contains 60 cm high water is moved in the cabin of elevator. Determine the pressure in kPa at the bottom of the tank when the elevator is stationary. Include the free body diagram in your solution. a.7.69 b.5.89 c.6.46 d.4.09
The 500 kg load on the hydraulic lift is to be raised by pouring oil (p = 780 kg/m^3) into a thin tube (Figure 3). Determine how high h should be in order to begin to raise the weight.
Water from a reservoir is raised in a vertical tube of internal diameter D = 30 cm under the influence of the pulling force F of a piston. Determine the force needed to raise the water to a height of h = 1.5 m above the free surface. What would your response be for h = 3 m? Also, taking the atmospheric pressure to be 96 kPa, plot the absolute water pressure at the piston face as h varies from 0 to 3 m.
Determine also the pressures P1, and P3, at sections 1 and 3 respectively if the pressure P2, at section 2 is 85.5 kPa
Q 244 What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
.........TheGaugePressure 0f the air in an aut0m0bile tire is 25psi, and assuming the ambient atm0sphericPressure is38psi. Express the_abs0lute_pressure_in the tire in bars.
Determine the volume of the body (s=3.0) that is required to keep the gate in the position indicated in the figure. The gate is 2.40m wide and 4.2m long.