A d.c.series generator has armature resistance of 0.5 Q and series field resistance of 0.032.It drives a load of 50 A.If it has 6 turns/coil and total 540 coils on the armature and is driven at 1500 r.p.m.,calculate the terminal voltage at the load.Assume 4 poles, lap type winding, flux per pole as 2 mWb and total brush drop as 2 V.

A d.c.series generator has armature resistance of 0.5 Q and series field resistance of 0.032.It drives a load of 50 A.If it has 6 turns/coil and total 540 coils on the armature and is driven at 1500 r.p.m.,calculate the terminal voltage at the load.Assume 4 poles, lap type winding, flux per pole as 2 mWb and total brush drop as 2 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A long shunt compound dc generator delivers a load current of 69 A at 396 V and has armature, series field and shunt field resistances of 0.096 Ω, 0.014 Ω, and 259 Ω, respectively. Calculate the armature current in ampere.
A 4 pole dc shunt generator with a shunt field resistance of 100 ohm and an armature resistance of 1 ohm has 378 wave connected conductor in its armature. the flux per pole is 0.02wb, if the load resistance of 10 ohm is connexted across the aemature terminal and the generator driven at 1000rpm, calculate the power obsorbed by load
A short shunt compound DC generator supplies a load current of 10A at a voltage of 10 volts. If the resistance of armature, shunt field and series field windings are 0.001 ohm, 1 ohm 0.00 ohm respectively. a) Draw the the figure. And find the generated voltage.
A long shunt compound dc generator delivers a load current of 78 A at 466 V and has armature, series field and shunt field resistances of 0.077 Ω, 0.04 Ω, and 290 Ω, respectively. Calculate the armature current in ampere (up to four decimal places).
A long shunt compound DC generator delivers a load current of 150A at 230V and has armature, series field and shunt field resistances of 0.032, 0.015 and 92Ωrespectively. Calculate (i) induced emf (ii) total power generated and (iii) distribution of this power (iv) voltage regulation
A short shunt compound DC generator supplies a load of 10A at a voltage of 10 volts. If the resistances of Armature, shunt field and series field windings are 0.01 ohm, 1 ohm and 0.00 ohm respectively. c) Write down the factors to improve the generated voltage.
A long shunt compound de generator delivers a load current of 70 A at 384 V and has armature, series field and shunt field resistances of 0.098 ohms, 0.026 ohms, and 264 ohms, respectively. Calculate the armature current in ampere.
A short shunt compound DC generator supplies a load of 10A at a voltage of 10 volts. If the resistances of Armature, shunt field and series field windings are 0.01 ohm, 1 ohm and 0.00 ohm respectively. c) write down the factors to improve the generated voltage. Generated Voltage is 10.2 V
A 500-V, wave-wound, 750 r.p.m. shunt generator supplies a load of 195 A. The armature has 720 conductors and shunt field resistance is 100 Ω. Find the demagnetising amp-turns/pole if brushes are advanced through 3 commutator segments at this load. Also, calculate the extra shunt field turns required to neutralize this demagnetisation.
A short shunt compound DC generator supplies a load current of 10A at a voltage of 10 volts. If the resistance of armature, shunt field and series field windings are 0.001 ohm, 1 ohm 0.00 ohm respectively. c) write down the factors to improve the generated voltage.
In a 120 V compound generator, the resistances of the armature, shunt and series windings are 0.06 2, 25 N and 0.04 2 respectively. The load current is 100 A at 120 V. Find the induced e.m.f. and the armature current when the machine is connected as (i) long-shunt and as (ii) short-shunt. How will the ampere-turns of the series field be changed in (i) if a diverter of 0.1ohm be connected in parallel with the series winding ? Neglect brush contact drop and ignore armature reaction.
. When a self-excited compound DC generator supplies load, the terminal voltage is not the same as the generated emE Why? a) voltage drop across the armature resistance will reduce the voltage available at the load terminals b) where there is a series field, voltage drop across the series field resistance will reduce the voltage available at the load terminals c) both "a" and "b" d) neither "a" nor "b"