A dam is subjected to a varying load as shown w1 kN/m w1 w2 w3 X y X (x+3) m 17 28 32 12 20 m w2 kN/m kN/m kN/m kN/m m y w3 kN/m Determine the following: ANSWERS IN ABSOLUTE VALUE AND IN THREE (3) DECIMAL PLACES • Resultant Force along vertical axis/line = • Resultant Force along horizontal axis/line = • The Resultant Force = • The angle of the Resultant Force with respect to vertical axis/line = KN KN KN deg

A dam is subjected to a varying load as shown w1 kN/m w1 w2 w3 X y X (x+3) m 17 28 32 12 20 m w2 kN/m kN/m kN/m kN/m m y w3 kN/m Determine the following: ANSWERS IN ABSOLUTE VALUE AND IN THREE (3) DECIMAL PLACES • Resultant Force along vertical axis/line = • Resultant Force along horizontal axis/line = • The Resultant Force = • The angle of the Resultant Force with respect to vertical axis/line = KN KN KN deg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.13 The resultant of three tensions in the guy wires anchored at the top of the tower is vertical. Find the un- known but equal tensions T in the two wires. All three wires and the tower are in the same vertical plane. mom x won goalsq sr 11 JAG BESHI BRIGH AGU Figure 2.52
3- Draw the graphs of the axial forces, shear forces and bending moments for the beam shown in the figure below, then choose the appropriate value for the following: 20 KN A bending torque 3m The reaction in the predicate A Axial force at point B Shear strength in the middle of the sill 20 KN B 141.4 O O O 3m 16 KN/m с 215.6 O O O O 5m D 20 O O 32.7 O O O 12.7 O O
Given: TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C2 1.0 * 0.208 0.1406 L 1.2 0.219 0.1661 0.1958 1.5 0.231 2.0 0.246 0.229 0.249 2.5 0.258 3.0 0.267 0.263 4.0 0.282 0.281 0.291 0.312 5.0 0.291 L 10.0 0.312 00 0.333 0.333 T Wood: Allowable stress: 5 MPa Shear Modulus: 0.5 GPa L= 0.6 m d = 50 mm What is the largest safe torque, in Nm, can be applied to the circular cross- section? (Provide answer in whole numbers, without the units. Ex: 123.4 Nm - -> 123) Your answer What is the largest safe torque can be applied to the rectangular cross-section? (Provide answer in whole numbers, without the units. Ex: 123.4 Nm --> 123) Your answer
18 - At point O in the figure F1 = 19i + 24j F2 = -13i + 17j F3 = -15i - 8j F4 = -37i - 11j Find the sum of the vectors. What is the strength of the resultant vector? A) 50.99B) 53.62C) 51,26D) 52.03E) 55,62
The cantilever beam is loaded as shown in Figure Q2 (b). Use method of moment area to determine slope at point B and deflection at point C. Take EI as constant.
Thank you
If the block is 1000kg, determine the value of frictional force if P is equal to 3200N. Usubstatic=0.50, Usubkinetic=0.35. A. 9810N B. 0 C. None of these D. 4905N
1) Solve for the x-component and y-component of the Resultant force, magnitude of the Resultant force (3 pts, 1 pt solution) A 30 AN 30 KN 30 KN 30 KN
DETERMINE THE VALUE OF "P" SUCH THAT RAY IS TWICE AS MUCH THE VALUE OF RBY. DEFINE THE VALUES OF SUPPORTS. 4.50 KM/m •ZKYM ZKN 1A 2.25m 0.00m 0.50 m 0. 20 0.75m P XB
Replace this loading by an equivalent resultant force and specify its location, measured from point A. (Hint: break-down the trapezoid-shaped distributed loading into a rectangular uniform load and a triangular distributed load, as shown) 200 lb/ft 500 lb 150 lb/ft 6 ft -3 ft -3 ft- B Soo 16
Your direct manager has called you for a meeting and provided you with the below schematic design that is shown in Figure 1 of a steel beam that might be implemented at one of the sites. 1000 N/m 500 N B .3 m- L 5 m – 5 m– 2000N Figure 1: Steal Beam The beam is subjected to a point load 500 N and a distributed load of 1000 N/m, and its weight is 2000 N acts downwards at the middle of the beam. a. Determine the equivalent force of the distributed load. b. Sketch the beam with all the applied forces (including reaction and equivalent forces) and allocate them into the proper points. c. Evaluate the values of the reaction forces at pin support at A and the rocker support at B (Knowing that the beam is in equilibrium). Activ ,Go to S
The clockwise angular velocity of the link AB shown in (Figure 1) is WAB = 3.2 rad/s. Figure C 4 in.- @AB 45° 5 in. 45° A 90° B D 3 in. < 1 of 1 Part A Determine the angular velocity of the connecting link BC at the instant shown. Express your answer in radians per second to three significant figures. 197| ΑΣΦ ↓↑ vec WBC = Submit Part B WCD= Submit Request Answer Determine the angular velocity of the connecting link CD at the instant shown. Express your answer in radians per second to three significant figures. IVE 41 Π| ΑΣΦ | | Provide Feedback Request Answer www vec ? rad/s ? rad/s