At the instant shown the boomerang has an angular velocity w=4 rad/s, and its mass center G has a velocity VG = 6 in./s. (Figure 1) Figure 1.5 in Sin. <1 of 1 Part A Determine the z and y components of the velocity of point B at this instant. Express your answers using three significant figures separated by a comma. 197| ΑΣΦΑ (UB)z. (UB)y= Submit Request Answer < Return to Assignment vec Provide Feedback ? in. /s

At the instant shown the boomerang has an angular velocity w=4 rad/s, and its mass center G has a velocity VG = 6 in./s. (Figure 1) Figure 1.5 in Sin. <1 of 1 Part A Determine the z and y components of the velocity of point B at this instant. Express your answers using three significant figures separated by a comma. 197| ΑΣΦΑ (UB)z. (UB)y= Submit Request Answer < Return to Assignment vec Provide Feedback ? in. /s

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter8: Time And Time-related Variables In Engineering

Section: Chapter Questions

Problem 24P

See similar textbooks

Similar questions

The circular disk of radius r = 0.40m rotates about a fixed axis through point O with the angular properties omega w= 2.2 rad/s and alpha a= 3.3 rad/s 2 with directions as shown in the figure. Determine the instantaneous values of the velocity and acceleration of point A.
Given the acceleration-time diagram sketch the velocity-time diagram and determine the displacement at time=9s.
Situation 2: The displacement (in meter) of a particle moving along x - axis is givenby x=At^2 + B , where A = 2m and B = 3m. Calculate average velocity between t =3sand t = 5s.Situation 2: Calculate instantaneous velocity at t = 5sSituation 2: Calculate instantaneous acceleration.
. An open cylinder tank 0.5 m in diameter and 1 m in height is completely filled with water and rotated about its axis at 240 rpm. Determine the volume of water spilled out of the tank. Unit of the Correct Answer: liters Decimal Places required in the final answer: 2 An open cylindrical tank 3m high and 1.5m in diameter contains 2m high of water. If the cylinder rotates about its geometrical axis, what constant angular velocity can be attained if the depth of water at the center is 0.5m? Unit of the Correct Answer: rad/sec Decimal Places required in the final answer: 3 A vertical cylindrical tank is 9 m high and 5 m in diameter. It is two thirds full of water and is rotated uniformly about its axis until on the point of overflowing. Compute the linear velocity at the circumference of the tank. An open cylindrical vessel 2m diameter and 4.2 m depth is 2/3 full of water. If rotated about the vertical axis at constant angular speed 80 rpm, determine the amount of water in…
At the instant when u = 90°, the motor on the car wash sprayer in Figure P7.38 rotates counter-clockwise at 150 rpm and accelerates at 200 rad/s2. Use the relative acceleration method to graphically determine the angular velocity and angular acceler-ation of the nozzle arm.
Rotation of the radially slotted arm shown in the figure below is governed by Ѳ = 0.2t + 0.02?^3, where ‘Ѳ’ is in radians and ‘t’ is in seconds. Simultaneously, the power screw in the arm engages the slider B and control its distance from O according to r = 0.2 + 0.04?^2, where ‘r’ is in meters and ‘t’is in seconds. a. What is the distance of the slider from point O after 4 seconds?b. What is the velocity of the slider after 4 seconds?c. What is the acceleration of the slider after 4 seconds?
Determine the moment of inertia (in mm4) of the given figure with respect to y axis if y=90 mm and z=55 mm. Round off only on the final answer expressed in whole number.
A ball of mass 5kg and a block of 12 kg are attached by a light weight cord that passes over a frictionless pulley of negligible mass as shown in the figure. The block lies on a frictionless incline of angle 30 degrees. Find the magnitude of the acceleration of the two objects and the tension in the cord. Take g = 9.81 m/s^2.
A 500 N block is resting on an inclined plane and is subjected to a constant force of 600N acting parallel to the inclined plane. After the block has moved 3 m from rest along the inclined plane the force 600N is removed. The inclined plane has a slope of three vertical to four horizontal. Coefficient of friction is 0.20 a. Which is the following gives the distance that the black will move further along the inclined plane until it will stop? b. Which of the following gives the velocity of the block when this for 600 Newton was removed? c. Which of the following gives the velocity of the block when it returns to its initial position?
A rock is thrown under a bridge at an initial speed of 10 m s − 1 and an angle of 36.9 degrees from the vertical, as shown. At the same time, a boat is passing under the bridge traveling 6 m s − 1 in the direction shown. See the note on the formula sheet about the values of trigonometric functions for this angle. a) Find the vertical and horizontal components of the initial speed of the rock seen by a person on the bridge. Clearly indicate your choice of axes in your drawing. b) Find the vertical and horizontal components of the initial speed of the rock seen by the person in the boat. Clearly indicate your choice of axes in your drawing. c) Draw a clear vector diagram showing how to relate the speed with which the rock appears to be moving when viewed from the bridge, the speed with which the rock appears to be moving as seen by the person on the boat and the speed of the boat with respect to the bridge.
Show the complete solution and the necessary graphs/diagrams. Use 2 decimal places in the final answer. The rotation of the 0.9-m arm OA about O is defined by the relation Eq. (1), where θ is expressed in radians and t in seconds. Collar B slides along the arm in such a way that its distance from O is Eq. (2), where r is expressed in meters and t in seconds. After the arm OA has rotated through 30°, determine the velocity of the collar (m/s).
k = D10*(γw/μ)*(C*e3)/(1+e) Where does this formula come from, it is not one that I could find in our class notes. Also how was the dynamic velocity calculated?