(a) Derive the following general relations ᎥᎢ T av (ii) (3)s (ii) (3) др —¿ [T (31), −³], Ср Cv др ᏭᎢ [T(r), -v] ᏭᎢ In each case the quantity on the left-hand side is the appropriate thing to consider for a particular type of expansion. State what type of expansion each refers to. (b) Using these relations, verify that for an ideal gas (T/V) = 0 and (ƏT/ǝp) H = 0, and that (T/V)s leads to the familiar relation PV = constant along an isentrope (a curve

(a) Derive the following general relations ᎥᎢ T av (ii) (3)s (ii) (3) др —¿ [T (31), −³], Ср Cv др ᏭᎢ [T(r), -v] ᏭᎢ In each case the quantity on the left-hand side is the appropriate thing to consider for a particular type of expansion. State what type of expansion each refers to. (b) Using these relations, verify that for an ideal gas (T/V) = 0 and (ƏT/ǝp) H = 0, and that (T/V)s leads to the familiar relation PV = constant along an isentrope (a curve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the coefficient of volume expansion of argon at 150 C? 2 points a)1 b)0.0023 c)0.0077 d)0.0067 e)not sufficient information
มอเตอร์เหนี่ยวนํา 3 เฟส 50-Hz ที่เชื่อมต่อดาวโรเตอร์ให้ 500 V (r.m.s.) หยุดนิ่งระหว่างวงแหวนสลิปบนวงจรเปิด คํานวณกระแสและตัวประกอบกําลังเมื่อหยุดนิ่งเมื่อขดลวดโรเตอร์เชื่อมต่อกับวงจรภายนอกที่เชื่อมต่อกับดาวซึ่งแต่ละเฟสมีความต้านทาน 10 Ωและการเหนี่ยวนํา 0.04 H ความต้านทานต่อเฟสของขดลวดโรเตอร์คือ 0.2 Ω และการเหนี่ยวนําคือ 0.04 H. นอกจากนี้ให้คํานวณตัวประกอบกระแสและกําลังเมื่อแหวนลื่นลัดวงจรและมอเตอร์ทํางานด้วยการลื่นไถล 5 เปอร์เซ็นต์ สมมติว่าฟลักซ์คงที่ [10.67 A; 0.376; 21.95 A; 0.303||
19 - A) 4000 NB) 8000 NC) 24 000 ND) 6000 NE) 10 000 N
A 1.5-kg mass attached to an ideal massless spring with a spring constant of 20.0 N/m oscillates on a horizontal, frictionless track. At time t = 0.00 s, the mass is released from x = 0.0 cm with a velocity of 0.370 m/s to the left. Find the followingA. Time periodB. Total mechanical energy of the massC. AmplitudeD. Phase constant of motion. Discuss the two possible values of phase constant you get and explain how you arrived at the correct answer. Write the equation of motion.E. Maximum acceleration of the mass. (Acceleration is maximum when it ispositive). How long after the release does the maximum acceleration occur?F. Draw the position-time graph for one cycle of motion.
Suppose a steel part is subject to to stress states: State one has a completely reversing stress amplitude of 32 ksi and state two have a completely reversing stress amplitude of 41 ksi. Further, suppose that in high cycle finite life region of the S-N diagram the relationship between stress and life is given by S = 95.1N^-0.0851 where S is in ksi and N is in Cycles. According to our methods, if this part is subjected to 29506 cycles at state one how many cycles of remaining life can we expect at state two? Answer must be in cycles
1) An electric motor’s torque is a function of the speed at which it rotates. Many brushed AC motors have a linear toque curve as shown below. If the power output of the motor is equal to the torque (T) multiplied by the rotational speed in rad/s (w), what is the maximum power you can get out of the motor if the stall torque (Tstall) is 0.001 Nm and the no load speed (wno load) of 10,500 RPM? Give answer in Watts.
what is the critical point termperature of water is a. 0.01 0C b. 373 0K c. 373 0C d. 647.15 0C
As a phase line, use a U-shaped curve. Let its downward-sloping segment intersect the 45 degree line at point L, and let its upward-sloping segment intersect the 45° line at point R. Answer the following five questions: (a) Is this a case of multiple equilibria? (b) If the initial value y0 lies to the left of L, what kind of time path will be obtained? (c) What if the initial value lies between Land R? (d) What if the initial value lies to the right of R? (e) What can you conclude about the dynamic stability of equilibrium at L and at R, respectively?
Why is the Fourier transform used in reciprocal space in Bragg's Law?
Find the coefficient of volume expansion of argon at 150 C? A) 0.0077 B) 1 C) not sufficient information D) 0.0067 E) 0.0023
finite element method If the nodal displacement for the element in figure (d) question no 1 is Calculate the displacement at point (1,3).
Give definition of unreliability F(t)of a component as function of time.