(c)A cast iron piston for a single acting four stroke engine has thefollowing specifications:Cylinder bore 100mmStroke=125mmMaximum gas pressure = 5 N/mm²Indicated mean effective pressure = 0.75 N/mm²Mechanical Efficiency = 80%Fuel Consumption = 0.15kg per brake power per hourHigher Calorific value of fuel = 42X10³ kJ/kgSpeed=2000 r.p.m.Stating any assumptions made, determine the thickness of the piston headPiston Data:Thermal conductivity of cast iron: 46.6W/m/°CTemperature difference between the piston centre and edge: 220°C.Permissible Stress for cast iron: 38N/mm²Take C=0.05.

Answered: Image /qna-images/answer/00c6ad75-27fd-48ee-973e-53d8daed1b5a.jpg

Answered: (c) A cast iron piston for a single…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If an engine has a bore of 0.1 m, stroke of 0.08 m, inlet flow effective area of 4.0 × 10−4 m2, and inlet temperature of 320 K, what is the maximum speed it is intended to be operated while maintaining good volumetric efficiency?
A V12, 4 stroke, normally aspirated piston engine develops a brake mean effective pressure of 14atm, having a piston stroke of 130mm, a cylinder bore of 140mm and operates at 3000rpm in sea-level-standard ambient conditions. The internal efficiency is 73% and the charge mass flow is 0.4kgs-1. Find a) The Brake Power b) The Indicated Power c) The indicated mean effective pressure d) The volumetric efficiency ηv (Air density at sea level standard = 1.225kgm-3)
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.
Calculate the air standard efficiency of a four stroke Otto cycle engine with the following data:Piston diameter (bore) = 137 mm; Length of stroke = 130 mm ; Clearance volume 0.00028 m3.Cp=1.004 kJ/kgK and Cv= 0.717 kJ/kgK
The following data refers for the single cylinder 4 stroke diesel engine. The brake power is 73 kW and engine speed is 500 rpm. The break mean effective pressure is 8 bar and mechanical efficiency is 80 %. The BSFC of the engine is .30 kg/kWhr of the fuel calorific value of 43200 kJ/kg. Determine indicated thermal efficiency.
There are developed 1063 kW at 267 rpm by an 8-cylinder, 2-stroke, 40.64 x 50.8 cm, diesel engine thatuses 0.082 kg/s of fuel with heating value of 42,571 kJ/kg. The indicated mean effective pressure is 562kPa Determine (a) brake thermal efficiency (b) indicated thermal efficiency (c) mechanical efficiency
A single-acting, four cylinder, 4 stroke cycle diesel engine with a bore to stroke 21.59 cm x 27.94 cm, operating at 275 rpm, consumes 8.189 kg/hr of fuel whose heating value is 43,961 kJ/kg. The indicated mean effective pressure is 475.7 kPa. The load on the brake arm, which is 93.98 cm is 113.4 kg. What is the brake arm mean effective pressure?
What is the engine speed (in rpm) required for good volumetric efficiency for an engine with two inlet and two exhaust valves, bore of 0.086 m, stroke of 90 mm, inlet air temperature of 330 K, exhaust temperature of 900 K and inlet valve diameter 30 mm (each). Assume specific heat ratio =1.37, R = 287 J/kg.K and an average inlet flow coefficient 0.4. Select one: a. 7013 O b. 6350 O c. 7847 O d. 4620 e. 9202
DIESEL CYCLE An ideal Diesel engine operates on 0.5 kg/s of air with a suction state of 100 kPa and 45oC. The pressure at the end of compression is 3.25 MPa, and the cut-off is at 6% of the stroke from head-end dead center position. Determine: a. compression ratio b. percent clearance c. network d. thermal efficiency e. mean effective pressure
A four cylinder two-stroke petrol engine with stroke to bore ratio 1.2 develops 35 kW brake power at 2,200 rpm. The mean effective pressure in each cylinder is 9 bar and mechanical efficiency is 78%. Determine: Diameter and stroke of each cylinder
. A six-cylinder two-stroke cycle marine diesel engine with 100 mm bore and 120 mm stroke delivers 200 B.H.P. at 2000. R.P.M. and uses 100 kg of fuel per hour. If I.H.P. is 240, determine the following: (a) Torque, (b) Mechanical efficiency, (c) Indicated specific fuel consumption.
A 6.4-liter, V8 Spark ignition (8 cylinder) 4-stroke engine operates at an engine speed of 3200 RPM. The compression ratio is CR = 10.5:1. At this speed volumetric efficiency is 93%, combustion efficiency is 98%, indicated thermal efficiency is 47%, and mechanical efficiency is 86%. Stroke and bore will be related by S = 0.90 B. Combustion starts at 18 degrees bTDC and last for 0.25 seconds. Calculate? a.Overall efficiencyb. Piston displacementc. Cylinder bore and stroked. average piston speed and max piston speede.distance piston has traveled from TDC at the end of combustion, f. volume at the end of combustion g. position of crank at the end of combustion

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS