a) Determine the Area and the centroid of the shape. Show the calculations using integration. b) Find the Area Moment of Inertia about the X-axis using integration. Then find the Area Moment of Inertia about the x-x centroidal axis (x-bar) using the Parallel Axis Theorem. 2.0 in c) Find the Area Moment of Inertia about the Y-axis using integration. Then find the Area Moment of Inertia about the y-y centroidal axis (y-bar) using the Parallel Axis Theorem. 2.0 in-

a) Determine the Area and the centroid of the shape. Show the calculations using integration. b) Find the Area Moment of Inertia about the X-axis using integration. Then find the Area Moment of Inertia about the x-x centroidal axis (x-bar) using the Parallel Axis Theorem. 2.0 in c) Find the Area Moment of Inertia about the Y-axis using integration. Then find the Area Moment of Inertia about the y-y centroidal axis (y-bar) using the Parallel Axis Theorem. 2.0 in-

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.78P: The L806010-mm structural angle has the following cross-sectional properties:...

See similar textbooks

Similar questions

Verify the centroidal z-coordinate of the pyramid shown in Table 8.3 by integration.
Find the centroid of the truncated parabolic complement by integration.
The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the catenary is the shape of a cable suspended between two points). Locate the y-coordinate 0f the centroid of the catenary by numerical integration using x=25ft.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Using integration, compute the polar moment of inertia about point O for the circular sector. Check your result with Table 9.2.
The moment of inertia of the plane region about the x-axis and the centroidal x-axis are Ix=0.35ft4 and Ix=0.08in.4, respectively. Determine the coordinate y of the centroid and the moment of inertia of the region about the u-axis.
The L806010-mm structural angle has the following cross-sectional properties: Ix=0.808106mm4,Iy=0.388106mm4, and I2=0.213106mm4, where I2 is a principal centroidal moment of inertia. Assuming Ixy is negative, compute (a) I1 (the other principal centroidal moment of inertia); and (b) the principal directions.
Using integration, locate the centroid of the area under the n-th order parabola in terms of b, h, and n (n is a positive integer). (b) Check the result of part (a) with Table 8.1 for the case n = 2.
Using the method of composite areas, find the dimension h that maximizes the centroid coordinate y of the plane region shown.
For the surface shown in the figure below, determine:a) The xc and yc coordinates of its centroid;b)The moments of inertia and product of inertia in relation to the centroidal axes x' and y' (axes parallel to x and y , which pass through the centroid);c)Using Mohr's circle, the new moments and product of inertia obtained by rotating these centroidal axes by 35° counterclockwise.
b=5 cm , h=8 cm . Find the centroidal distance from X axis
Find the centroid x bar of the shaded area and the moment of inertia along x or y axis Please make the answer clear and detailed,thank you