(a) Determine the reactions at A and E if P = 740 N. The reactions are positive if to the right or up, negative if to the left or down. (b) What is the maximum value which Pmay have for static equilibrium? Neglect the weight of the structure compared with the applied loads. 29, 4390 N 2.9 m 4.7 m 4.7 m Answers: (a) If P = 740 N, Ax = -1695.83 N Ay= 724.56 Ex= 3824.14 (b) The maximum value which P may have for static equilibrium: Pmax

(a) Determine the reactions at A and E if P = 740 N. The reactions are positive if to the right or up, negative if to the left or down. (b) What is the maximum value which Pmay have for static equilibrium? Neglect the weight of the structure compared with the applied loads. 29, 4390 N 2.9 m 4.7 m 4.7 m Answers: (a) If P = 740 N, Ax = -1695.83 N Ay= 724.56 Ex= 3824.14 (b) The maximum value which P may have for static equilibrium: Pmax

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.54P: The mechanism of negligible weight supports the weight W. Find the value of for equilibrium. Is the...

See similar textbooks

Similar questions

What is Equilibrium of a Rigid Body? Give an example.
When F = 300 N with Θ = 40°, what is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads.
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work. These are my answers FBD=2F, RAX=353.5N RAy= 353.5N but am not sure if a correct any help
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work.
Based on the figure below, derive the equilibrium equations, in terms of tension, shown below:
As shown, a load of magnitude PPP is applied to a structure. Assuming that all members are weightless and that ABEF and BCD are rigid bodies, find the magnitudes of the reactions at D and G needed to maintain the structure in equilibrium. Assume the following values: aaa_c = 4.50 mm , bbb_c = 3.00 mm , and PPP = 104 NN .
A straight, uniform bar weighing 60lb rests in a horizontal positon between two frictionless slopes. A concentrated load of 200lb acts at distance x from the right hand slope. Determine x and reaction forces assuming that the bar is in static equilibrium.
Brief explanation of Equilibrium of a Rigid Body and an example
The upper end of the bar of a problem is now leaned against a non vertical wall. Determine the minimum value of the angle θ for which equilibrium is possible for μs = 0.25 and for μs = 0.50
The weight of hom0 bar AB is 11kN, F is 45kN, and bar AB is in equilibrium. Calculate the direction (in degrees) and magnitude (in kN) of the reaction at point A.
Two rods AC and CE are connected by a pin at C and by a spring AE . The constant of the spring is k , and the spring is unstretched when θ = 30°. For the loading shown, derive an equation in P,θ ,I, and k that must be satisfied when the system is in equilibrium.
What are rigid body equations of equilibrium?