A diffuser is used to slow the flow of water as shown in the figure above. Water flows through the system at a rate of 0.10 m/s. The upstream diameter is 10 cm, and the water pressure is 10 kPa, while the downstream end the diameter increases to 20 cm. Determine the force acting on the support due to water flow. Express your result in kN,

A diffuser is used to slow the flow of water as shown in the figure above. Water flows through the system at a rate of 0.10 m/s. The upstream diameter is 10 cm, and the water pressure is 10 kPa, while the downstream end the diameter increases to 20 cm. Determine the force acting on the support due to water flow. Express your result in kN,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal pipe has an abrupt expansion from D1 = 5 cm to D2 = 10 cm. The water velocity in the smaller section is 8 m/s and the flow is turbulent. The pressure in the smaller section is P1 = 410 kPa. Taking the kinetic energy correction factor to be 1.06 at both the inlet and the outlet, determine the downstream pressure P2, and estimate the error that would have occurred if Bernoulli’s equation had been used.
(Open System) A garden hose attached with a nozzle is used to fill a 10 gal bucket. The inner diameter of the hose is 2cm and it reduces to 0.8 cm at the nozzle exit. If it takes 50s to fill the bucket with water, determine a) volumetric flowrate( L/s) and mass flowrate (kg/s) of the water through the hose b) average velocity of water at the nozzle exit (m/s)
A fan draws 1.42 m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan mechanical is 70% and air is measured at 25 0C and 760 mmHg. Using p water formulaPw=
7. Water flows steadily with a velocity of 4m/s in a horizontal pipe having a diameter of 16.24cm. At one section of the pipe, the temperature and pressure of the water are 220C and 688kpa respectively. And at a distance of 305m downstream, the pressure is 75.44psi. Determine the hydraulic gradient.
A pump is 2.2 m above the water level in the sump and has a pressure of –20 cm of mercury at the suction side. The suction pipe is of 20 cm diameter and the delivery pipe is short 25 cm diameter pipe ending in a nozzle of 8 cm diameter. If the nozzle is directed vertically upwards at an elevation of 4.2 m above the water sump level, determine the power input in KW into the flow by the pump. Neglect all losses. a.20.31 b.24.04 c.0.10 d.0.52
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.
A turbine is placed at the bottom of a 20-m-high water body. Water flows through the turbine at a rate of 30 m3 /s. If the shaft power delivered by the turbine is 5 MW, the turbine efficiency is (a) 85% (b) 79% (c) 88% (d) 74% (e) 82%
N2O expands isentropically through a duct from p1 =200 kPa and T1 = 250°C to a downstream section wherep2 = 26 kPa and V2 = 594 m/s. Compute (a) T2; (b) Ma2;(c) To; (d ) po; (e) V1; and (f ) Ma1.
You have a 550 W pump with 70% efficiency available. Is it possible to use this pump to carry 10 m3/h of a liquid through a 4.7 cm inside diameter pipe, from one open tank to another, if the liquid is discharged at a point 10 m above the level of liquid in the suction tank and the total friction losses are 50 J/kg? The density and viscosity of the liquid are 1050 kg/m3 and 2 cp respectively.
Air enters a fan through a duct velocity of 6.3 m/s and an inlet static pressure of 2.5cm of water less than the atmospheric pressure. The air leaves the fan through the duct at a velocity of 11.25 m/s and a discharge pressure of 7.62cm of water above the atmospheric pressure. If, the density of the air is 1.2kg/m3and the fan delivers 9.45m3/s, what is the fan efficiency when the power input to the fan is 13.75 kW at the coupling. Show schematic diagram and provide solutions.
Q2// Water enters a hydraulic turbine through a 26 cm diameter pipe at a rate of 1.2 m^3/s and exits through a 21 cm diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 2 m. For a combined turbine generator efficiency of 91%. determine the net electric power output. Disregard the effect of the kinetic energy correction factors.
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is ( WITH FREE BODY DIAGRAM) CHOICES: A.7.12 B.6.21 C.8.7 D.5.05