Steam enters a control yolume that has one inlet and two exis. At the inlet (location 1) with a diameter of 5.2 cm, the Steam has 100 bar, 360°C , and a mass flow rate of 2 kg/sec. Through one exit (location 2), 15.% of the incoming mass flow rate Teaves the Control volume and the remainder leaves through the other exit locatión 3). For Steady state operaton, calculake . Dthe mass flow rate at lo cation 3 in kg/sec using 5 signifigan figures... है

Steam enters a control yolume that has one inlet and two exis. At the inlet (location 1) with a diameter of 5.2 cm, the Steam has 100 bar, 360°C , and a mass flow rate of 2 kg/sec. Through one exit (location 2), 15.% of the incoming mass flow rate Teaves the Control volume and the remainder leaves through the other exit locatión 3). For Steady state operaton, calculake . Dthe mass flow rate at lo cation 3 in kg/sec using 5 signifigan figures... है

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluidby varying the cross-sectional area. At the last section of a jetengine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s ata pressure of 500 kPa and a temperature of 600 K enters a nozzlewith an inlet cross-sectional area of 5 m2. The exit area of thenozzle is 20% of its inlet area. The air leaves the nozzle at avelocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (iv) Determine the temperature of the air as it leaves the nozzle.(v) Calculate the pressure of the air as it leaves the nozzle.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
P23. Steam enters an insulated nozzle with negligible velocity, 200 psi and 500°F. Steam exits at 100 psi and 400°F.For steady-state operation and neglecting potential energy effects, determine the velocity of the steamleaving the nozzle in ft/s.
Steam flows at a steady state through a converging insulated nozzle, 25cm long and with an inlet diameter of 5cm. At the nozzle entrance (state 1), the temperature and pressure are 325C and 700kPa and the velocity is 30ms1 At the nozzle exit(state 2), the steam temperature and pressure are 240C and 350kPa. What is the outlet volume and what will the diameter be, using steam tables?
A two stage compressor with first stage piston displacement of 94,390 cu.m/sec is driven by a motor. Motor output is 35 HP, suction temperature 22 degC, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105deg C and 44 degC, respectively. Final discharge pressure is 100 psi gage, while suctionis estimated to be 14.4 psi. Determine the compression efficiency.
air vessel of water flows at a pressure of 10 bar and 180'C into a turbine, located in a chemical plant and there it expands reversibly and adiabatically to a final pressure of 1.05 bar. Calculate the final specific volume, temperature and increase in entropy. Neglect changes in velocity and elevation. If the mass flow rate is 6.5 kg / min, evaluate the heat transfer rate from the gas and the power delivered by the turbine. Assume water to be a perfect gas and C₁ = 0.837 kJ / kg K. new 6.o
The absolute steam entry velocity of a single-stage impulse turbine is 600 m/s, nozzle angle is 20°, ratio of blade speed to whirl component of steam speed is 0·5, blade velocity coefficient is 0·85. Find- (a) the blade angles at inlet and outlet if the steam enters without shock and leaves the blade in an axial direction, (b) power developed if the steam flow rate is 5 kg/sec, (c) blade or diagram efficiency and (d) axial thrust.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
8.. Nitrogen gas is compressed . Pressure rises from 100 kPa to 1500 kPa. Initial temperature of 25 deg C. The required mass flow is 1000 kg/hr. Would you recommend single stage or multi-stage compression? Justify your recommendation with appropriate calculations. For Nitrogen, R = 0.297 kJ/ kg K, g = 1.4, r = 1.25kg/m3, µ = 17.4 µPa s, cp = 1.039 kJ/kg K
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
A single acting two-stage air compressor deals with 4 m^3/min of air under atmospheric conditions of 1.013 bar and 15°C with aspced of 250r.p.m. The delivery pressure is 80 bar. Assuming complete inlercooling, find the minimum power required by the compressor and the bore and stroke of the compressor. Assume a pistonspeed of 3 m/s, mechanical efficiency of 75 percent, and volumetric efficiency of 80 percent per stage. Assumethe polytropic index of compression in both the stages to be it = 1.25 and neglect clearance.
Consider a diffuser operating at steady-state. Air flows in with a velocity of 300m/s, a pressure of 1 bar, and a temperature of 70 ºC. The outlet is at 1.5 bar and 107 ⁰C.What is the exit velocity? What is the ratio of exit area to the inlet area of the diffuser?