A distributed load is applied to beam AB, shown in the diagram below. The beam is supported by a roller support at A and a pin support at B. Calculate the magnitude of the reaction force at support A. (Calculate answer in units of N. Enter numeric answer only to one decimal place (e.g., 10.2). No units in answer) F=3m; E = 14 N/m A 3m 30° w = E Fm B

A distributed load is applied to beam AB, shown in the diagram below. The beam is supported by a roller support at A and a pin support at B. Calculate the magnitude of the reaction force at support A. (Calculate answer in units of N. Enter numeric answer only to one decimal place (e.g., 10.2). No units in answer) F=3m; E = 14 N/m A 3m 30° w = E Fm B

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 23P

See similar textbooks

Similar questions

2. Given: X = 100 kg; Y = 150 kg Solve for the acceleration of block X in m/s2 for Case 2. Ignore the friction and mass of pulleys. (3 significant figures)
Answer is 1,022.80. Show your solution. Forces F1 and F2 shown below act on the screw eye. If F1 = 501 lb, determine the magnitude of the resultant force (in lb) if it is directed vertically upward. Use F2 = 578 lb., α = 20°.
For the beam and loading shown in Figure below, determine the beam deflection at point H. Assume that EI = 8 × 104 kN·m2 is constant. Express your answer in mm and use three decimal places. Indicate the negative sign in your final answer if the deflection is downward.
Q. A block of 150 N is placed on the surface having coefficient of friction 0.4 (shown in figure). What force is required to just enable the block to move. Consider two cases related to force (a) Pushing force (b) Pulling force
1. A force of 450 N is exerted on lever AB as shown in the figure. End B is connected to a piston which fits into a cylinder having a diameter of 60 mm. What force FD acts on the larger piston, if the volume between C and D is filled with water?
A basketball player hangs from the hoop when performing a "dunk" by exerting 2 forces of 100 pounds on it at the indicated points. The bounded dimensions are as follows: h = 14.5 in, r = 9.5 in, α = 120 °. If the indicated forces are replaced by another force applied at point O, which will generate the same effect as the original system. Determine the values of the new force and the torque M that is generated.
F1 = 4 kNF2 = 3 kNF3 = 2 kNa = 3 mb = 5 mc = 4 mtheta = 33 degrees Find the magnitude of the resultant couple moment (in kN-m).If the calculated answer is not whole number, express it in 4 significant figures. If the value is negative, include a negative sign.
Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 2m x 5m gate shown in the figure. Pressure of air = 47 kPa Fluids: fluid a (s=3.8) fluid b (s=0.27) fluid c (s=1.68) h1= 0.9 m h2= 1.6 m h3= 3.9 m Round your answers in 3 decimal places
Pitot tube is an instrument that is used to measure flowrate in a pipe. Figure 3 shows water flowing through a pipe with pitot tube attached to a U-tube manometer containing Fluid X. Given the difference in height in the manometer, h, calculate the flowrate through the pipe by showing the application of Bernoulli Equation and Hydrostatic Pressure Equation. Details of the parameters are as follows; Difference in manometer, h = 0.1 m Density of water = 1000 kg/m3 Density of Fluid X = 12000 kg/m3 Diameter of pipe = 0.3m
Figure shows a slender uniform rod with mass M and length L. It might be a baton held by a twirler in a marching band (without the rubber end caps). (a) Use integration to compute its moment of inertia about an axis through O, at an arbitrary distance h from one end. (b) Initially the rod is at rest. It is given a constant angular acceleration of magnitude a around the axis through O. Find how much work is done on the rod in a time t. (c) At time t, what is the linear acceleration of the point on the rod farthest from the axis?
Consider the frame shown in (Figure 1). Suppose that F1 = 3.5 kN. a) Determine the x and y components of the force that the pin at B exerts on the frame using scalar notation. b) Determine the x and y components of the force that the pin at A exerts on the frame using scalar notation. Express your answers in kilonewtons to three significant figures. Enter your answers separated by a comma.
A cylindrical tank containing a fluid (sg = 0.75) is accelerated upward by a net force of 40 lb. The volume of the fluid is 1.60 cu. ft. If the depth of the fluid is 3 ft, determine the force acting on the bottom of the tank. 4 decimal places answers