A single angle tension member, L 4 x 4 x 3/8 in. made from A36 steel is connected to a gusset plate with 5/8 in. diameter bolts, as shown in Figure below. The service loads are 35 kips dead load and 15 kips live load. Determine the adequacy of this member using AISC specification. Assume that the effective net area is

A single angle tension member, L 4 x 4 x 3/8 in. made from A36 steel is connected to a gusset plate with 5/8 in. diameter bolts, as shown in Figure below. The service loads are 35 kips dead load and 15 kips live load. Determine the adequacy of this member using AISC specification. Assume that the effective net area is

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.1P

See similar textbooks

Similar questions

If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
Channel sections are used as a purlin. The top chords of the truss are sloped at 5H to 2V. Trusses are spaced 5m on centers and the purlins are spaced 1.4m on centers. Use the properties of the channel section given below. Loads: (Consider all loads pass thru the centroid of the section.) Dead load = 750 Pa Live load = 1,000 Pa Wind load = 1,400Pa Wind coefficients: Windward = 0.3 Leeward = -0.5 Use Fbx=Fby=250 MPa. Determine the maximum value of the interaction equation using the load combination of 0.75(D+L+W)
1. An unsymmetrical flexural member consists of a 70 × 600 topflange, a 70 x 400 bottom flange, and a 12 × 180 web.a, Determine the Section Modulus.b. Determine the distance from the top of the shape to the horizontalplastic neutral axis.c. If A572 Grade 50 steel is used, what is the plastic moment MPy forthe horizontal plastic neutral axis?
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
Plz do not use gpt if u use chatgpt i will downvote you again don't use chatgpt
an angle bar 100x100x11 mm tension member is connected with 20-mm-dia bolts as shown in the fig. both legs of the angles are connected. use fy=248 MPa and Fu=400 MPa. 1. determine the nominal strength for tensile yielding in the gross section. a. 515.59 kN b. 429.67 kN c. 545.60 kN d. 390.10 kN 2. determine the effective net area of member a. 1573 mm^2 b. 1632 mm^2 c. 1605 mm^2 d. 1815 mm^2 3. determine the nominal strength for tensile rupture in the net area. a. 642 kN b. 730 kN c. 554 kN d. 650 kN
Determine the plastic moment strength (kN-m) of a C15x50, A36 steel, about the minor axis d = 381 mm bf = 94.39 mm tw = 18.19 mm tf = 16.51 mm
Determine: Ix & ly = Moment of inertia about axis XX and YY Rx & Ry = Radius of gyration about axis XX and YY Sx & Sy = Elastic modulus about axis XX and YY steel specs are here http://www.toolsforengineer.com/steel-sections-properties-tables/ FOR WIDE FLANGE = W250X22FOR ANGLE BAR = L32X32X6.4
Channel sections are used as a purlin. The top chords of the truss are sloped at 5H to 2V. Trusses are spaced 5m on centers and the purlins are spaced 1.4m on centers. Use the properties of the channel section BELOW. Loads: (Consider all loads pass thru the centroid of the section.) Dead load = 750 Pa Live load = 1,000 Pa Wind load = 1,400Pa Wind coefficients: Windward = 0.3 Leeward = -0.5 Use Fbx=Fby=250 MPa. Determine the maximum value of the interaction equation using the load combination of 0.75(D+L+W)
Channel sections are used as a purlin. The top chords of the truss are sloped at 6H to 1V. Trusses are spaced 4m on centers. Use the properties of the channel section in the picture. Loads: Dead load = 600 Pa Live load = 800 Pa Wind load = 1,300Pa Wind coefficients: Windward = 0.25 Leeward = -0.4 Use Fbx=Fby=248 MPa. Determine the safe spacing of purlins (Use load combination of 0.75(D+L+W)
Compression member.
Give an correct answer with proper method or i will give an dislike A cantilever beam of effective depth 315 mm has span of 2.5 m. The percentage of tensile reinforcement is 1.5% Fe-250 bars. Check the beam for its depth for deflection only. Take M20 conerete.