A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.5 cm and 5.5 cm respectively. The difference between the two waveforms is 0.2. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform

A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.5 cm and 5.5 cm respectively. The difference between the two waveforms is 0.2. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 14RQ: A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow,...

See similar textbooks

Similar questions

A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Q22/ A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 40 ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 5.9 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.1 cm and 5.5 cm respectively. The difference between the two waveform is 0.4. Determine a) Frequency, b) Phase difference, c) Peak value value of G waveform. AND RMS value of H waveform.
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 5.3 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.6 cm and 5.9 cm respectively. The difference between the two waveforms is 0.7. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform a) frequency
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 40 ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 5.5 cm and 5.3 cm respectively. The difference between the two waveform is 0.8. Determine a) Frequency, b) Phase difference, c) Peak value value of G waveform. c) RMS value of H waveform.
The period of this signal is about------ ms (milliseconds). The oscilloscope range selector determines the scale on the screen. That means number of volts per line for amplitude vertical (v/div) and the number of milliseconds per line for time horizontally (ms/div).
ii) A double beam oscilloscope displays 2 square waveform G and H. The time / cm switch is on 2ms / cm and the volt / cm switch on 4 V / cm. The width of each complete cycle is 6.2 cm for both the waveform. The Peak to Peak height of waveform G and Hare 4.1 cm and 5.5 cm respectively. The difference between the two waveforms is 0.5. Determine a) Frequency, b) Phase difference, c) RMS value of G waveform
Two signals of identical voltage, amplitude and frequency, but different phase are fed to a cathode ray oscilloscope, one to the X plates and another to the Y plates.Sketch and briefly explain what form of trace you would get if the phase difference was:(a.) zero, (b.) 90°, and (c.) 180°
A double beam oscilloscope displays 2sine waveforms A and B. The time/cm switch is on 100us/cm and the volt/cm switch on 2V/cm. The width of each complete cycle is 5cm for both the waveforms. The height of waveforms A and B are 2cm and 2.5cm respectively. Determine their a) frequency, b) phase difference, and c) peak and r.m.s value of voltages. The difference between the two waveforms is 0.5 cm.
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 20 ms/cm, and the 'volts/cm' switch is set to 30 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (iii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees and (v) R.m.s value of waveform Q.
Explain how you would use an oscilloscope to measure an alternating potential difference of the order of 10V peak-to-peak. (You may assume that an alternating PD of 5V peak-to-peak is available).What is the RMS value of a peak-to-peak voltage of 10.0V?
Please explain the waveforms, what are the reason why does the 3rd waveform (Recovered signal) is attenuated. 1st waveform: Carrier signal (2Vpk,20 kHz) 2nd waveform: Information signal (1Vpk,1kHz) 3rd waveform: Recovered signal