Identify all the forces applied in the FBD. show complete FBD and solution. 30 mins left. (a) Draw the FBD of wedge B and block A when wedge B impends to slide to the right. Friction is negligible except for thecontact surfaces between B and the horizontal plane B whose coefficient of friction is 0.20. (b) Determine P to impend thewedge B to slide to the right.30120 fbB80 lb

Answered: Image /qna-images/answer/bea4b4ac-f6cd-4721-8042-0974c5b8a162.jpg

Answered: (a) Draw the FBD of wedge B and block A…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter8: Influence Lines

Section: Chapter Questions

Problem 10P

See similar textbooks

Similar questions

The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 0.4 between both collars and the rod determine the maximum supporting force available from friction when F = 0 and when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 618.75
The Q-kg industrial door with mass center at G is being positioned for repair by insertion of the 5° wedge under corner B. Horizontal movement is prevented by the small ledge at corner A. The coefficients of static friction at both the top and bottom wedge surfaces are 0.66. Calculate the rightward force P' which would remove the wedge from under the door. Assume that corner A does not slip for your calculation of P'. Q = 402
Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
Fixed end support at A and rollers at B and C . A concentrated load of 12 KN at the mid span of BC.Use slope deflection method and constant value of El with E= 200,000 MPa and 1= 400 x 106 mm^4. What is the moment MBC and MABin KN-m? 2 decimal places
The tripod shown is to support a vertical load W and horizontal load P at point D. The legs of the tripod rest on a level rough surface at points A, B and C. If W=150N, P=50N, a = 0.5m, b =0.75m. c=1.125m, d=1.5m, 19. Determine the force acting on leg AD. Determine the force acting on leg BD.
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2Determine the following;C. Slope at L/3. D. Deflection at L/3.
36 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, By=? a) 0B) 48C) 24D) NoneE) 14
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
answer this: determine the deflection at point D i knm3/EI
Two forces act on the screw eye. If F1 = 400 N andF2 = 600 N, determine the angle θ (0° ≤ θ ≤ 180°) betweenthem, so that the resultant force has a magnitude ofFR = 800 N.
Q5. Crank OA Rotates With Uniform Angular Velocity 0, = 4 Rad/s Along Counterclockwise. Take OA= = 0.5 M, AB=2r, And BC = V2r. For The Instant, P=45, OA Is Horizontal And AB Is Vertical. Determine The Angular Velocity
A rectangular lamina with its side measuring 50 * 60 mm rests with one of its shorter edgesin HP and the other in VP. The plane is inclined at 30n to the HP. Draw its plan andelevation. Obtain the shortest distance of the plane from the ground line

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

SEE MORE TEXTBOOKS

(a) Draw the FBD of wedge B and block A when wedge B impends to slide to the right. Friction is negligible except for the contact surfaces between B and the horizontal plane B whose coefficient of friction is 0.20. (b) Determine P to impend the wedge B to slide to the right. 30 120 b B 80 lb