A drone will be used for a rescue mission. As an engineer, you are requested to choose the most suitable drone for the operation. The aim is to arrive at the exact location as fast as possible. The altitude position responses of three drones (4, B, C) to a unit step input is shown in Figure Q.1. Based on the responses, select the best drone to perform the mission. Provide reasons for the selection by comparing with other drones. Also describe the disadvantage of the selected drone. 1.4 1.2 Step Response 0.8 0.6 C 0.4 0.2 2.5 5 7.5 10 12.5 15 Time (seconds) Altitude position

A drone will be used for a rescue mission. As an engineer, you are requested to choose the most suitable drone for the operation. The aim is to arrive at the exact location as fast as possible. The altitude position responses of three drones (4, B, C) to a unit step input is shown in Figure Q.1. Based on the responses, select the best drone to perform the mission. Provide reasons for the selection by comparing with other drones. Also describe the disadvantage of the selected drone. 1.4 1.2 Step Response 0.8 0.6 C 0.4 0.2 2.5 5 7.5 10 12.5 15 Time (seconds) Altitude position

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 3R: a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____...

See similar textbooks

Similar questions

Assuming that the beta is 100. Can you explain this how to approach and method to this problem? Thank you very much! And also can you do this as fast as you can? I would really appreciate it!
Q3 Power flow (load flow) is an important part of any power system studies. (A) In relation to a power system: Explain three of the key assumptions that are made in developing the fast-decoupled power flow technique and why these assumptions are often reasonable for a high voltage power grid, Discuss the reasons that make the load flow problem nonlinear. In a 20 Bus power system with 5 buses that have generating units, determine the number of PV buses, PQ buses and buses where the voltage magnitudes are known. Justify your answer.
Give an example of a second-order, constant-coefficient, homogeneous equation with non-real roots of the characteristic equation. Write down the linear system that corresponds to it. Can you find an example of an interconnected system of two tanks that is described by this system? Explain. Then solve the system.
Subject: control Discuss the effect of adding a pole on the root locus shape , through the relative stability.
Qa) What is the value of ?(∞)?Qb) What is the equation of V1
Control system! (a) For what ranges of α and β is the closed-loop system stable and (b) Given that β is fixed at some positive value, for what value of α is the closed-loop systemmarginally stable and what are the associated locations in the s-plane of those marginally stable poles?
Each item below describes key characteristics of a particular system (that is, a plant transfer function). For each system, describe the effect of proportional control on the stability of the closed-loop system. Specifically, 1) what can you say for small gains, and 2) what for large gains? (E.g., stable, unstable, inconclusive.) Provide a short explanation of your answers, with sketches as necessary.
In this scenario, a person wants to select clothing to wear for an event. The overall combination is to have pants, shoes, and a shirt. Within these categories, the person can choose between a polo shirt (P) and a collared long sleeve shirt (C). For shoes, the person is deciding between loafers (L) or dress shoes (D). For pants, the person could choose slacks (S) or jeans (J). The person will only wear one item from each set at a time. How could a circuit be designed that outputs all the possible clothing combinations (F)?
In the figure, the steady state error is required to be 1% for the ramp entry r (t) = 0.1 h (t) input to the system. a) Determine the type (N) number and K(OL) value of the open loop system. b) Given the input and the desired maximum steady state error, what would be the smallest value of K? c) What should Td be chosen in order to keep the system stable according to the selected K value?
Consider the circuit is shown in the figure below. The circuit comprises a voltage supply, ?(?), resistor (?), inductor (?) and capacitor (?). Let ?1 = ? and ?2 = ?? be the state variables for this system, where ? and ?? are the circuit current and capacitor voltage, respectively. For this system,a) Derive the loop equation, involving integro-differential equations, from first principles b) Write the state differential equationsc) Write the state-space equation in matrix-vector formd) sketch the signal flow graph
The characteristic equation of control system is given as following. S3 + 6s2 + 11s + 6(1 + Kc) = 0 Determine: 1. The Value of Kc for which the control system is stable. 2. The roots of the characteristic equation for the value of Kc for which the system is on the threshold of instability.
Explain what ll means in the Zeq equation? How do you solve the equation