A dual slider mechanism is driven anti-clockwise by a crank rotating at a constant angular speed of 1200 rpm as shown in Fig Q3. Crank OA is 300 mm in length, connecting rod AB is 500 mm in length and connecting rod AC is 515 mm in length. 30% 30% (45 0 Fig Q3 Determine the relative angular velocities of connecting rods AB and AC.

A dual slider mechanism is driven anti-clockwise by a crank rotating at a constant angular speed of 1200 rpm as shown in Fig Q3. Crank OA is 300 mm in length, connecting rod AB is 500 mm in length and connecting rod AC is 515 mm in length. 30% 30% (45 0 Fig Q3 Determine the relative angular velocities of connecting rods AB and AC.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wheel of mass m, radius r and radius of gyration k is rolling along a horizontal road with hub velocity v in the +ve x direction. Brakes are applied to the wheel, providing a torque of -M, slowing the vehicle to rest. Assuming that the wheel rolls without slipping and the hub position starts at x=0, where m = 10 kg, r = 0.85 m, k = 0.595 m, v = 5m/s, M = 21 Nm, g = 9.81 m/s^2 a) Find the constant acceleration, (ax) of the wheel hub b) Find the minimum static coefficient of friction (mu) between the road and the wheel c) Find the stopping distance (smax) and time (tmax)
A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
Consider a person holding a vacuum cleaner (idealized as Bar AB). The point where the person holds the handle (point A) is constrained to move along the vertical and has a velocity of 0.12 m/s downwards and is increasing its speed at a constant rate of 0.4 m/s2. This is to move the tail end (Point B) of the cleaner. The tail end of the cleaner has a velocity of 0.0840 m/s to the right and the vacuum cleaner has an angular velocity of 0.0586 rad/s.a) What is the the magnitude of the angular acceleration of the vacuum cleaner (Bar AB)? (1.313, 3.5, 0.875, 1.969) b) What is the magnitude of the acceleration of block B? (0.521, 0.270, 0.1929)
Crank OA = 75 cm with an angle of 30oC with respect to horizontal;OP = 50 cm; CA = 150 cm; CD = 135 cmNote that the line of motion of slider D is in straight line with frame P solve:a. Maximum swing angle of the slotted lever CPb. Maximum total length of stroke of slider Dc. Quick Return Ratio (QRR) of the mechanism
An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? througha gear box as shown Figure Q1(b). The rope that carries the load and spiral spring are encircled on a pulley with diameter 1.2m. Gear box ratio is 0. 1 and gear box efficiency is 100%, while gear box equivalent moment inertia is 5.55 km?. Neglect friction effect in this drive system and assume spiral spring force is X newtonCalculate the torque of the motor needed to bring up the load with acceleration1.2 m/s?.
Q#03 : In a four-bar chain ABCD, Link AD is fixed and is 160 mm long. The crank AB is 40 mm long and rotates at 150+25 rpm clockwise. While Link CD is 70mm long and oscillates about point D. BC and AD are of equal length, angle BAD=60°. Find the angular velocity of Link CD? (Subject : mechanics of machines)
A metal spherical shell bearing, m1=1.2 kg, r1=22 cm, is rotating on a metal rod of negligible mass about its center at ω1i=15 rad/s. A flywheel (solid disk), m2=3.1 kg, r2=11 cm, rotating at ω2i=-8 rad/s collides so that the flywheel is now on the rod through its center. Find the angular speed of the system if the friction was negligible.
Consider the slider-crank mechanism shown. Crank AB is 0.500 m long and is rotating counterclockwise at 3.00 rad/s. Rod BD is 1.500 m long. 1. Which of the following gives the closest value of the speed of end B of crank AB? 2. If crank AB is rotating at a constant angular velocity, which body/bodies is/are in general plane motion?
A solid cylinder (mass 1.2kg, radius 5.0cm) on a horizontal table is connected to a block (mass 200 g) via a pulley (mass 0.80kg, radius 10.0cm) via a light, rigid string. Draw free body diagram for each of the object 1) list the dynamic and kinematic equations that related to all three objects. 2) find the acceleration of the falling block 3) fnd the angular acceleration of the cylinder and the friction force on it
Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, and μs=0.297. What is the maximum angular velocity allowable if the collar is to remain at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
A single cylinder reciprocating engine has speeded 300 RPM. Stroke 250 mm, mass of reciprocating parts 50 kg. Mass of revolving parts at 150 mm radius 37 kg. If two fourth of the reciprocating parts and all the revolving parts are to be balanced, find (i) The balance mass required at 400 mm radius (ii) The residual unbalanced force when the crank has rotated 45° TDC.
A flywheel is fitted to a multi cylinder engine, which runs at a mean speed of 360 r.p.m. If the speed varies from 6 % above the mean to 2 % below it and the fluctuation energy is 1200 kN-cm, If the radius of gyration is 20 cm, find (i) mass moment of inertia of the wheel and (ii) mass of flywheel. The mass moment of Inertia in Kgm2 is Mass of the flywheel in kg is