Q5 Two large containers A and B of the same size are filled with different fluids. The fluids in containers A and B are maintained at 0° C and 100° C, respectively. A small metal bar, whose initial temperature is 100° C, is lowered into container A. After 1 minute the temperature of the bar is 90° C. After 2 minutes the bar is removed and instantly transferred to the other container. After 1 minute in container B, the temperature of the bar rises 10°. How long, measured from the start of the entire process, will it take the bar to reach 99.9° C?

Q5 Two large containers A and B of the same size are filled with different fluids. The fluids in containers A and B are maintained at 0° C and 100° C, respectively. A small metal bar, whose initial temperature is 100° C, is lowered into container A. After 1 minute the temperature of the bar is 90° C. After 2 minutes the bar is removed and instantly transferred to the other container. After 1 minute in container B, the temperature of the bar rises 10°. How long, measured from the start of the entire process, will it take the bar to reach 99.9° C?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
A mass of 300kg of oil is cooled in 1 hour from 70 celcius to 35 celcius in a cooler consisting of a bank of tubes through which hot oil passes. Cooling water circulates around the outside of the tubes. Calculate the mass of cooling water required per hour if the water temp increases by 21 degrees celcius . Specific Heat of Oil - 2.0 kJ/kg deg C Specific Heat of Water - 4.186 kJ/kg deg C
3. A classroom that normally contains 40 people is to be air-conditioned with window air-conditioning units of 5-kW cooling capacity. A person at rest may be assumed to dissipate heat at a rate of about 360 kJ/h. There are 10 light bulbs in the room, each with a rating of 100 W. The rate of heat transfer to the classroom through the walls and the windows is estimated to be 15,000 kJ/h. If the room air is to be maintained at a constant temperature of 210C, determine the number of window air-conditioning units required. draw a figure also, and explain each step by step solution.
In many manufacturing plants, individuals areoften working around high-temperature surfaces.Exposed hot surfaces that can cause thermal burns on humanskin are considered hazards in the workplace. Metallic surfacesabove 70° C can instantly damage skin that touches them.Consider an AISI 1010 carbon steel strip (? = 7832 kg/ m 3 )2 mm thick and 3 cm wide that is conveyed into a chamber tobe cooled at a constant speed of 1 m/s. The steel strip entersthe cooling chamber at 597° C. Determine the rate at whichheat needs to be removed so that the steel strip exits the chamberat 47° C . Discuss how the conveyance speed can affect therequired rate of heat removal.
Discuss the application of the first law of thermodynamics to a mountaineer who eats food, gets warm and perspires a lot during a climb, and does a lot of mechanical work in raising herself to the summit. The mountaineer also gets warm during the descent. Is the source of this energy the same as the source during the ascent?
n electric generator at a power plant produces energy by passing superheated steam from a high temperature container (reservoir), through a pipe connected to a series of fans, and then into a low temperature reservoir. As the steam passes across the blades of the fans some of the heat energy of the steam is transformed into mechanical energy, which turns the fans which in turn are connected to a generator, which in turn converts the mechanical energy into electrical energy. If the high temperature steam has a temperature of 412.1 K and the low temperature reservoir has a temperature of 105.4 K, what is the Carnot efficiency of this process?
A monatomic ideal gas initially fills a V0 = 0.45 m3 container at P0 = 85 kPa. The gas undergoes an isobaric expansion to V1 = 0.75 m3. Next it undergoes an isovolumetric cooling to its initial temperature T0. Finally it undergoes an isothermal compression to its initial pressure and volume. (a). Calculate the work done by the gas, W1, in kilojoules, during the isobaric expansion (first process). (b). Calculate the heat absorbed Q1, in kilojoules, during the isobaric expansion (first process). (c) Calculate the heat absorbed Q2, in kilojoules, during the isovolumetric cooling (second process). (d) Calculate the change in internal energy by the gas, ΔU2, in kilojoules, during the isovolumetric cooling (second process). (e) Calculate the work done by the gas, W3, in kilojoules, during the isothermal compression (third process). (f) Calculate the heat absorbed Q3, in kilojoules, during the isothermal compressions (third process).
A mass of ice at -7 C is needed to cool 224 kg of vegetables (Cp = 3.35 KJ /kg.K )in a bunker for 24 hours. The initial temperature of the vegetables is assumed to be 29 C . It is also assumed that the average temperature in the bunker is 7C within the 24 -hour period . If the heat gained per hour in the bunker is 25% of the heat removed to the vegetables from 29 C to 7C, what would be the required mass of ice ? show t-s diagram
Describe what happens to the system inside of a refrigerator or freezer in terms of heat transfer, work, and conservation of energy. Confine yourself to time periods in which the door is closed.
A box with a mass of 3m is on frictionless ground, attached to a wall (on the left-side of the box) by a spring with constant k. Inside the box (on the frictionless floor of the box), is a block of mass m. The block is also attached to the left-side of the box (but inside it), by a second spring, with a spring constant 2k/5.1) What are the F = ma equations for the box and the block? (Remember how the motion of each, affects each other)2) What are the matrices K and M for the system?3) What are the normal frequencies of the system?4) Describe the motion of the masses. In phase? Out of phase? Does one mass oscillate with a higher amplitude than the other?
Indirect Cooling With Liquid Nitrogen. You are designing a system to cool an insulated silver plate of dimensions 2.00 cm × 2.00 cm × 0.60 cm. One end of a thermally insulated copper wire (diameter D = 2.70 mm and length L = 18.0 cm) is dipped into a vat of liquid nitrogen (T = 77.2 K), and the other end is attached to the bottom of the silver plate.(a) If the silver plate starts at room temperature (65.0 °F), what is the initial rate of heat flow between the plate and the liquid nitrogen reservoir?(b) Assuming the rate of heat flow calculated in part (a), estimate the temperature of the silver plate after 30.0 seconds.