A factory need a drive system for a conveyer system. Voltage source available is three phase 415(a)Volt, 50 Hz. Electric motor that they use is DC motor.(i) How the design of DC drive system for that system :(ii) What the parameters should be considered?(iii) What type of the DC motor that needed?(iv) What kind of converters that suitable for this system?(v) How the control system?(b) (1) Suggest a DC motor drive which can cause very fast heating of an automobile? Show circuitdiagram in case of series excited motor. (2). Propose an energy efficient braking control mechanism thatcan be used for practical traction systems. (Hint: The supply is partly receptive)A DC-to-DC converter is an electronic circuit or electromechanical本D(c)device that converts a source of direct current (DC) from one voltage level toanother. In the given circuit when switch Q2 (lower switch) is turned on themotor act as a generator and the armature current rise why? How is the energysent back to source in such a converter?v,本D

a) i) The design of DC drive system is given below,

Answered: A factory need a drive system for a…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter34: Motor Installation

Section: Chapter Questions

Problem 7RQ: A 100-HP three-phase squirrel-cage induction motor is connected to 480 volts. The conductors...

See similar textbooks

Similar questions

1. Identify the DC motor that can be used in conveyor. Also, explain the requirement of a DC Motor to be selected as a drive motor for conveyor.
Given a 25 hp, three-phase, 230-volt, squirrel cage induction motor. The ambient temperature of the place ofinstallation is 40°C. Use TW wires
Your Answers may be presented through Discussions, Drawings/Figures/Diagrams, Reference to NEC/PEC and Computations What is the rated full-load current of a ¾-horsepower, 208-volt single-phase motor
Q about Control Systems. Looking for only SECOND question's answer
A 350-HP squirrel-cage induction motor is connected to a 480-volts three-phase feeder. The nameplate lists the following: HP 350, Service factor 1.10, Full-load amps 408, NEMA Code B. The conductors are to be copper with THWN insulation, and 600:5 current transformers are used to reduce the current supplied to the overload heaters. The motor circuit is protected with dual-element time delay fuses. Determine the conductor size, overload heater size using the chart shown in Figure 34-7, the NEMA and IEC starter sizes, and the fuse size for this installation.
Part 2: Analysis and selection of the Wind Turbine.The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. What are the two closed loop control systems that are used generally in wind turbines? How do they work? 2. Calculate the power density of the input power from the wind when the wind is blowing at the rated wind speed at the turbine height. Clearly show your steps in details.
In the distribution transformer;In the transformer used for the distribution of electricity to the houses, 3.3 kilovolts enters and 400 volts come out. When we make the phase-neutral calculation, that is, when we divide it by √3, we get 230 volts and 220 volts coming to the sockets. Where does the remaining 10 volts go? (Can you explain with figure) is this about 30 degree phase shift?
A 460VAC rated, 60 Hz, 125-Hp Three-phase induction type motor is to be connected for across-the-line starting. The nameplate indicates the motor’s maximum ampere rating, 160A. It has a NEMA code letter B. The ambient temp of the installation place is and TW copper will be used. Short-circuit protection device that will be used is Inverse Time Breaker. Calculate the Conductor size.
I'm having a difficulty in understanding this Design of Armature (Stator) of AC GENERATOR. PLEASE SHOW THE VERY DETAILED, NO SKIP/SHORTCUT WITH THE UNITS and SYMBOLS so that I can understand. Atleast maximum of 5 decimals. Given: Number of conductors = 29.25 (APPROXIMATE VALUE ONLY) 3 slots per pole per phase, 3-phase, 4 poles. Required: (A) Calculate the slots and slots per pole (B) Calculate the Conductors in each slot (C) Calculate the OFFICIAL VALUE of number of conductors. Final Answer: A. ?, ? B. 6.09 ≈ 6 conductors in each slot C. 48 conductors
22 The DC voltage is generated in the Armature winding of DC Generator. Select one: True False
True or false 1. One of the alternative of using DC Voltage is to use inverter. 2. In long-shunt DC generator, the shunt field winding is directly connected across the armature only. 3. The direction of magnetic lines of force of magnet is from south pole to north pole. 4. In DC supply, terminal polarity (positive and negative) are not taken into consideration. 5. Overload relay is part of direct-on-line magnetic starter power circuit.
Write a report on system control strategies and techniques used in engineering.

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS