A fan is to be selected to cool a computer case whose d see the figure). Half of the volume in the case is expect other half to be air space. A 5-cm-diameter hole is av nstallation of the fan that is to replace the air in the voic Small low-power fan-motor combined units are availab estimated to be 30 percent. Determine (a) the wattage of

A fan is to be selected to cool a computer case whose d see the figure). Half of the volume in the case is expect other half to be air space. A 5-cm-diameter hole is av nstallation of the fan that is to replace the air in the voic Small low-power fan-motor combined units are availab estimated to be 30 percent. Determine (a) the wattage of

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.31P

See similar textbooks

Similar questions

Describe the process of internal flow convection heat transfer in an annular tubeconcentric and draw
A gasoline engine is at a location where the temperature is measured to be 14.2 °C and produces 347 KW at 5800 rpm while consuming 0.0184 kg's of fuel. During operation, data shows that its mechanical energy loss is 18 %, the actual volume of air going into each cylinder is 80% (the volumetric efficiency has a negligible variation), and the actual fuel-to-air ratio is 0.065. What were the engine parameters at sea level conditions if the pressure here is 100.3 kPa and the temeratur here is 18 Uc hotter than that of the alevated conditions? Determine at sea-level conditions the ISFC in ka/kW-hr Use four (4) decimal places in your solution and answer.
It is planned to lift and move logs from inaccessible forest by means of air balloons. Helium at atmospheric pressure of 101.325 kPaa and temperature of 23.1oC is to be used in the balloons. What minimum balloon diameter will be required for a gross lifting force of 20 metric tons? (Consider k = 1.666 and R =2077.67 J/kg-K for Helium
A gasoline engine is at a location where the temperature is measured to be 14.8 °C and produces 300 kW at 5800 rpm while consuming 0.0184 kg/s of fuel. During operation, data shows that its mechanical energy loss is 18 %, the actual volume of air going into each cylinder is 80% (the volumetric efficiency has a negligible variation), and the actual fuel-to-air ratio is 0.065. What were the engine parameters at sea level conditions if the pressure here is 99.3 kPa and the temperature here is 18 0C hotter than that of the elevated condition? Determine at sea-level conditions the Brake Power in kW.
) A 75 mm-diameter orifice is on the verticalside of a closed tank. The tank rests on a flat groundand the orifice is 0.5 m above the ground. Filled withfour fluids with air on the topmost portion that is undera pressure of 15 KPa, and the rest of specific gravities of0.80, 1.0, and 1.50, respectively, the jet hits the groundat a horizontal distance of 3.75 m. If the liquids have thesame thickness, and the power lost in the system is 233watts, determine the following:(a) The initial discharge in L/s if C=0.63.(b) The thickness of each liquid in m.(c) The coefficient of contraction.
What is the function of V-cone flow element and manifold pressure measuring devices, where equipment this can applied and What manufacturing processes may they be found in?
8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of the stack necessary for a driving pressure of 0.20 KPaKindly answer all please. Thank you
What is the friction loss in cm of water in a 2.44m diameter chimney 61m high up which gas is flowing at 9.14 m/sec? Gas density is 0.6776 kg/m3.
Derive an expression for the change in height h in a circular tube of a liquid with surfacetension Y and contact angle θ , as in Fig. E1.8.
As3...Air at atmospheric pressure, 27 °C and %30 RH conditions and with a velocity of 3 m/s flowsparallel to a square water pool having the 10 m x 10m dimensions. Water in the pool is at 33•C. Determine the time required for the water height in the pool to decrease 10 mm.
For internal flow with fully developed flow condition The velocity profile .................... change and the thermal profile .............................. change in the direction of flow Please fill the blank Blank 1 ( Does or does not) Blank 2 ( Does or does not )
BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 13 - 1