H.W: A stationary power plant operating on an ideal Brayton cycle has a pressure ratio of 7. The gas temperature is 25 C at the compressor inlet and 1000 ° C at the turbine inlet. Utilizing the air standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine, (b) back work ratio and (c)the thermal efficiency. Answers: (a) 520 K, 730 K (b) 40.8%, (c) 42.7%

H.W: A stationary power plant operating on an ideal Brayton cycle has a pressure ratio of 7. The gas temperature is 25 C at the compressor inlet and 1000 ° C at the turbine inlet. Utilizing the air standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine, (b) back work ratio and (c)the thermal efficiency. Answers: (a) 520 K, 730 K (b) 40.8%, (c) 42.7%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gas turbine power plant working on Brayton cycle, Explain the working principle of the cycle with physical diagram as well as P-V and T-s diagrams, and with all the required details
PART D only A gas-turbine power generator operates on an ideal air-standard Brayton cycle 1 → 2 → 3 → 4 shown in Fig. 1. The gas temperatures at the compressor inlet, compressor exit, and turbine inlet are T1 = 300 K, T2 = 600 K, and T3 = 1200 K, respectively. Solve PART D below using the variable specific heat assumption PART D - Evaluate the thermal efficiency η of the cycle and the back work ratio rBW = wC/wT.
Q#1. A gas-turbine plant operates on the regenerative Brayton cycle, the schematic diagram of whichis shown in Fig. Q 1, with two stages of reheating and two-stages of intercooling between the pressure limits of100 and1200 kPa . The working fluid is air. The air enters the first and the second stages of the compressor at 300 K and 350 K , respectively, and the first and the second stages of the turbine at 1400 K and 1300 K , respectively. Assuming both the compressor and the turbine have an isentropic efficiency of 80%. The regenerator has an effectiveness ofεregen=75% . Assume variable specific heats (i.e., use the concept of relative pressures) and the intermediate pressuresof intercooling and reheating is the square root of the product of inlet and exit pressures for intercooling and reheating. Make other the necessary assumptions and determine(a) the back work ratio,β , and the net work output,, wnet(b) the thermal efficiency (that is the first-law efficiency,ηi ) and(c) the…
A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following: a. Pressure & temperature at each stateb. T-S diagramc. Heat Added, per unit mass
A gas-turbine power plant operating on an ideal Brayton cycle has a pressure ratio (P./P,= P./P.) of10. The air temperature is 27 °C at the compressor inlet and 1328 K at the turbineinlet. Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of thecompressor and the turbine, (b) the specific work, and (C) the thermal efficiency.
A gas turbine power plant operating on an ideal brayton cycle has a pressure ratio of 8. The gas temperature is 320k at the compressor inlet and 1400k at the turbine inlet. Using the air-standard assumptions, determines: 1. The back work raio 2. The temperature at the exits of the turbine and exits of the compressor 3. The thermal efficiency in decimals
IDEAL RANKINE CYCLE: In an ideal Rankine Cycle, steam at 5 MPaa and 500 o C enters the turbine and expands 300 KPaa. For 110,000 kg/hr of steam, find: a) Ideal power output of the Turbine (kW), b) Power to drive the pump (kW), c) Rate of Heat Added (kW), d) thermal efficiency of cycle and engine, e) steam rate of the cycle and engine, f) Heat Rate (PLEASE SHOW COMPLETE SOLUTION AND ENCLOSE ALL THE FINAL ANSWERS ROUNDED OFF TO THE 4TH DECIMAL)
27 - In the simple ideal Rankine cycle, the enthalpy of water at the turbine exit is 2300 kJ/kg. If the pressure at the turbine inlet is 8 MPa and the temperature is 550ºC, which of the following should the water flow rate be to obtain 110 MW power? a) 100kg/h B) 120kg/h NS) 110 kg/h D) 130kg/h TO) 90kg/h
Instead, assume variable specific heat A gas-turbine power plant operates on the simpleBrayton cycle between the pressure limits of 100 and 800 kPa.Air enters the compressor at 308C and leaves at 3308C at amass flow rate of 200 kg/s. The maximum cycle temperatureis 1400 K. During operation of the cycle, the net power outputis measured experimentally to be 60 MW. Assume constantproperties for air at 300 K with cv 5 0.718 kJ/kg·K, cp 51.005 kJ/kg·K, R 5 0.287 kJ/kg·K, k 5 l.4.(a) Sketch the T-s diagram for the cycle.(b) Determine the isentropic efficiency of the turbine forthese operating conditions.(c) Determine the cycle thermal efficiency.
At the beginning of the cooling process of an ideal Brayton cycle, the pressure and temperature of the air are 150 kPa and 480°C. The state of the air leaving the compressor is 1.2 MPa, 320°C. Assuming constant specific heats (R=0.287 kJ/kgK, cv=0.718 kJ/kg K, cp=1.005 kJ/kg K), determine the back work ratio of the cycle.
A simple Brayton Cycle uses helium as the working fluid, it has a maximum temperature of 1100 deg.K, and a pressure ratio of 3.3. At the start of the compression, the helium pressure and temperature are 90 kPa and 290 deg.K. Based upon cold-air standard analysis consumptions, determine the following: (a) T2 and T4 in deg.K (b) Heat added in kJ/kg (c) Turbine and Compressor Work in kJ/kg (d) Work net in kJ/kg (e) Cycle efficiency in % (f) Mean Effective Pressure in kPa
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 5. The turbine inlet temperature is 1127 °C. Assume cold-air analysis, determine the net power developed of the cycle. determine the thermal efficiency of the cycle. Determine the heat rejected to the condenser, in kW, determine the back work ratio. determine the input heat into combustor, in kW.