A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it applies a torque to the shaft equivalent to 2.2 kN-m. The allowable shearing stress in the key is 70 MPa. If the length of a key is 70 mm, determine the designed width of the key. 12 mm 14 16 15 mm.

A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it applies a torque to the shaft equivalent to 2.2 kN-m. The allowable shearing stress in the key is 70 MPa. If the length of a key is 70 mm, determine the designed width of the key. 12 mm 14 16 15 mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Related questions

Q: 5-4. Determine the load in member CH of the truss shown in Figure P5-4. 6 kips 15 kips CY BY D X 20'…

Q: 6. Water is pumped to a storage tank from a pool by a centrifugal pump. The elevation difference…

Q: 8. The force that keeps the body moving in circular motion is a) Centripetal force b) Centrifugal…

A: given data Q-8 what force keep the body in circular motion. Q-9 weight = 20 N mass = 2 kg radius =…

Q: A helical compression spring has a scale of 400 lbs/inch, an inside diameter of 2.5 inches, a free…

Q: 2. What is the specific gravity of an oil which has a Baume reading of 28 degrees?

A: Since you have posted multiple questions so we are solving only first question for you. If you want…

Q: Compute the input power Efficiency=38% Ouput power-410 J

A: Given data : Output power is denoted by O Efficiency is denoted by E Ratio of output power upon…

Q: Determine the requined force (P) to hold a card of (lokg) which is placed on inclined Surface as…

A: Given data Mass of cart = 10 kg Find the force P to hold the cart.

Q: 20 mm ↑ X 50 mm H 20 mm 175 mm y H 200 mm 20 mm H₂

Q: (b)show that: l(cosh at cos at) $3 st+4a4

Q: Establish the reasons of being similar of two turbomachines and Explain the significances c…

A: given; establish the reason of being similar of two turbomachines and explain the significance…

Q: A machine, subject to a harmonic force of 500N with 0.5Hz frequency, is modelled as a mass of 800kg…

Q: 2. A column is made of steel (E = 210 GPa) and has a rectangular (20 mm x 10 mm) cross section.…

Q: 5. Calculate the torque about point O due to the force in each of the situations in Figure S5.4 if…

A: Given data F1=40 NF2=30 NF3=40 N L=10 cm Here, F represents the force acting on the lever. Here, L…

Q: Describe the difference between a carrying capacity graph and what causes it's shape?

A: The typical population size of a species in a given habitat is referred to as carrying capacity.…

Q: 1 m 1 m 30° b. 0.5 m 0.5 m b 1m -75 mm-

A: Given Data The mass of the drum is:m=20 kg The supported diamter of frame is :D=2mm Now draw the…

Q: Calculate the thermal efficiency of an air standard limited pressure cycle with a compression ratio…

A: Given Compression ratio, r = 22 Heat input, Q = 1800 kJ/kg Find Thermal…

Q: load (KN) Elongation (mm) | PAL D 0-5 a. I 3-8 0.3 7-9 12.9 14-3 15-9 16.9 17-8 1.61 21-2 24-2 26-9…

A: Solution is given below:

Q: At cooling capacity greater than 50 tons of refrigeration 1 2 Eco friendly 3 A single unit capacity…

A: The solution is attached below:

Q: Please explain how to distinguish the types of defects that can be detected using X-Rays and AMI

A: Quality assurance specialists usually divide problems into three categories: minor, major, and…

Q: Cycle work of an air standard otto engine is 1100 kj/kg. Maximum cycle temperature is 3300 deg. C…

A: Given data Cycle work = 1100 kJ/kgMaximum cycle temperature = 3300 °CTemperature at the end of…

Q: at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. The water flow over…

Q: A tainter semicircular gate is shown in the figure. Considering a ft wide strip, determine the…

A: Givenγ=62.4 lbs/ft3r=5ftl=2.5ft

Q: Provide the sectional front view, looking at the direction X, draw the top view, and right-side view…

A: According to the details provided in the question we need to draw three projection views of the…

Q: What is the pressure at the bottom of 0.5m height fluid if the container moves 5m/s2 upward? Fluid…

Q: instantaneous position of a four-bar linkage mechanism is shown in figure 1. The input AB, rotates…

Q: Results First Experiment Gear set 2 lock - Driver pulley Gear set 1 unlock - Follower pulley Table 1…

Q: Numerate the practical applications of vapor refrigeration system.

A: Solution is attached below

Q: A 10,000 kg of fish is to be cooled from 30°C to-15°C for 16 hrs.The specific heat below freezing is…

A: Givenm=10000kgT1=30oCT2=-15oCt=16hrCs=1.8kJ/kgKCl=3.7 kJ/kgKLHF=290kJ/kgQ=20%Tf=-3oC

Q: Find the strain Stress=35.6 MPa Modulus of elasticity=54 MPa

A: Given data : Stress=σ Modulus of elasticity=E Required : Strain

Q: Given is a thin-walled tube with the following data: Wall thickness- 3mm Torque is 900 N.m Length of…

Q: In an I.C. Engine Mechanism the peripheral velocity of crank pin is constant at 150 cm/s. and it has…

A: We know that the peripheral velocity of the crank pin in an I.C. Engine Mechanism is constant at 150…

Q: alculate the thermal efficiency of an air standard limited pressure cycle with a compression ratio…

A: Find , Efficiency of cycle. Given information, Inlet conditions, Maximum pressure and heat input.…

Q: 60 tons R-22 refrigeration system has an evaporator temp.of -4°C and a condenser temp. of 30C.Find…

Q: Find the displacement value Work done=120 J Force=23 N

A: Given data : Work done is denoted by W Force is denoted by F Required : Displacement

Q: Question: A particle moves in the x-y plane with an x-component of velocity in meter per second…

A: given data Vx=4√t ay= 4e^t when t=4 , y=10, x=4 , and Vx=10 find equation of path and magnitude of…

Q: Find work done F=2.1 N Displacement=0.23 m

Q: Ms Chian conducted an experiment using Refrigerant-134a (R-134a). She filled an 80 litres vessel…

Q: A bicycle and rider is mass 125 kg are travelling at a speed of 10 km/hr. The rider applies a break…

A: We know that a 125 kilogramme bicycle and its rider go at a speed of 10 km/hr.The rider applies a…

Q: Q.4] Find the forces in the members of the bridge truss shown below. 5KW 5KN A k B k 12 m 8m с 10 KN…

Q: A bicycle and rider is mass 125 kg are travelling at a speed of 10 km/hr. The rider applies a break…

Q: Engineers investigate the compressibility of fluid for the aircraft hydraulics. You are required to…

Q: A 550 BHP diesel engine uses fuel oil of 30°API gravity and fuel consumption of 0.65 lb/BHP-hr. For…

A: Given data P=550 BHPBSFc=0.65 lb/BHP-hr Here, P is the power and BSFc is the mass flow rate or fuel…

Q: Block A has a mass of 50 kg, and block B has a mass of 15 kg. They are stacked, connected by a cable…

Q: Example 26.13 An axial-flow compressor draws air at 20°C and delivers it at 50°C. Assuming 50%…

Q: A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for use in moving it. What…

A: Given Force, F = 5000 lb Material = Rolled B1113 Find Size of the bolt, D

Q: Third Experiment - Compound Epicyclic Gear Driver pulley at gear set 2: Stationary gear = ring gear…

Q: Complete the table of values below. Then, sketch the graph of r = 2-3 cos in polar coordinate system…

A: Given r=2-3cosθ To find Plot the value of r with angle

Q: A pipe 12 mmm diameter with a velocity of 0.50 m/s is attached by a nozzle at the end having a…

A: Equating the volumetric flow rate

Q: n a refinery, fuel ethanol is flowing in a pipe at a velocity of 1.2 m/s at 2 atm. The refinery…

A: Given data v1=1.2 m/sP1=2 atmP2=1 atmd1=40 cmd2=10 cm Here, v is the velocity of flow and P is the…

Q: Find the stress Force=2 N Area=2 mm2

A: Given data : Force=F Area=A To find : Stress

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it applies a torque to the shaft equivalent to 2.2 kN-m. The allowable shearing stress in the key is 70 MPa. If the length of a key is 70 mm, determine the designed width of the key.
12 mm

14

16

15 mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft rotates at a speed of 679 rpm and transmits a power of 5 kW. If the maximum torque exceeds the mean torque by 23%. Take the value of allowable shear stress as 71 MPa. Find the value of the following i) Torque transmitted in N-m ii) Maximum torque transmitted in N-m iii) Diameter of the shaft in mm.
A 1.5-inch Monel shaft is used in a torsional application. Based on the operating speed of 100 rpm and factor of safety of 12. How much horsepower can it transmit? Assume the shearing stress is ¾ of the ultimate tensile stress which is 100 ksi.
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 200 inches determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
A shaft is 21/2 in. square, and the allowable shearing unit stress for the material is 6000 psi. The torque on the shaft is A. 27,600 in B 20,800 in C. 31,200 in D. 24,100 in
A single bolt is used to lap joint two steel bars together. Tensile force on the bar is 20,000 N. Determine the diameter of the bolt required if the allowable shearing stress is 70 MPa?