A fillet weld can be used to join which of the following joint types: * O All of the Mentioned

Q: Identify the elements applied to the following welding symbols.

A: Given: To determine: Welding symbols

Q: What are the grooves most often used for welding on mild steel pipe

A: Single V Single U Single J Single bevel grooves

Q: why are some weld joints grooved?

A: Welding is a material joining process in which two or more parts are coalesced at their contacting…

Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned O Tee…

A: Correct answer: All of the mentioned

Q: 9- Excess weld metal according to EN ISO 5817, t = 20.0 mm, measured : h = 6.7 mm b = 35.0 mm…

A: We can answer the first question since the exact one is not specified. Please resubmit the question…

Q: In addition to continuously changing the weld pattern,what other changes must be continually made…

A: Considered to be the most challenging pipe position is the 66 or 45° fixed inclined position.…

Q: Why should there be a space between the plates whenmaking a fillet weld on thick plates of a tee…

A: Fillet welding refers to the process of joining two pieces of metal together when they are…

Q: 5 Which of the following appropriate methods are adopted for reducing distortion in weldments?

A: When materials are welded together, because of the uneven cooling the stresses are induced in the…

Q: Design the above joint using welded connection. The w=15mm. The required length of weld is:

A:

Q: What two units are used to show the minimum shearstrength of a spot weld?

A: Resistance welding comes in the form of spot welding. One of the simplest and quickest methods of…

Q: 6) Residual stresses in the GMAW joint can be reduced through O Use of low coefficient of thermal…

A: Residual stresses in the GMAW joint can be reduced through Increasing the weld metal volume

Q: What is the safety factor for this weld? Fe678 iet, be1 in; de23 in; he14 in. The weld metal is…

A: Solution to Q21 as per our company policy:

Q: Why should convex weld faces be avoided?

A: Excessive Convexity This discontinuity can produce a notch effect in the welded area and,…

Q: Which of these welds could be analyzed using the AISC Code's "kips per inch" method? (Indicate all…

A: AISC stands for American institute of steel construction.It is basically quality management system…

Q: Why are all welds not inspected to the same level orstandard?

A: Information Provided: Not all welds undergo the same level or standard of inspection. Not all welds…

Q: What is the minimum acceptance criteria for porosity for visual inspection of lap welds?

A: Lap welding: When two metals are attached in a overlapping pattern on top of each other then this…

Q: when making a vertical weld and it appears that the weld metal is going to drip over the shelf, what…

A: In vertical weld, the welding is done from the bottom position to vertically upwards position. In…

Q: A soldering iron 'bit' is made of?    A.Brass    B.Tin    C.Steel    D.Copper

A: We can find the answer as below A soldering iron 'bit' is made of?

Q: Find the eccentricity of the welded connection by using 5 mm fillet weld. -120 mm - 200 mm 400 mm X-…

A:

Q: Q1) Prepare cross-sectional views of the following fillet weld and redraw the joints representing…

A: (i) Draw the cross sectional view.

Q: xplain the short circuiting arc weld cycle. NOTE:4-5 SENTENCES ONLY

A: Short circuiting arc weld cycle:  Short circuiting arc welding is a mode of metal transfer with low…

Q: Why must cast iron weld metal be ductile

A: Cast iron is the alloy of carbon and iron. Cast iron has high hardness due to presence of high…

Q: 24. Why is it important not to strike the arc outside of the weld joint?

A: Welding is a fabrication process in which two similar metals or dis similar metal are joined with…

Q: - What is mean by M24 X 2-RH 2-What is the function of a cover plate in riveted joints? 3- If a weld…

A: Given : M24 X 2-RH

Q: 7) Which type of FSW technique prevents plate thinning and hooking at advancing side of the weld…

A: Weld thinning and hooking in friction stir welding has been an inherent issue which affects the…

Q: Which of the following joints is a permanent joint? O A. Bolted joint O B. Riveted joint O C. Welded…

A: Permanent joint: The joint ensures a rigid mechanical attachment to parts over the entire process of…

Q: In which of the following welded joints do both the work pieces are in the same plane? O A. Lap…

A:

Q: After the weld is set up and ready to begin, how mightthe welder want to check for freedom of…

A: Welder method for determine the degree of freedom

Q: Which of the following is true about soft-soldered joints?   a. High power is required.   b. Can…

A: Soldering: Soldering is a metal-to-metal joining procedure in which solder is melted and used to…

Q: Please give me another Welded connections sample problems and solutions as a revi

A: Q. Determine the design strength of the tension member and connection system shown below. The…

Q: What helps hold the weld in place on a 4G weld?

A: 4G weld :-  It is an overhead position used for butt welds. Welders need to hold the torch from…

Q: 11)lf length of a fillet weld is I and leg length is h, then area of throat can be given by:

A: The length of the fillet weld is l. The leg length is h.

Q: 1) Match the Column A (Weld protection?. medium) with Column B (different fusion welding Process) -…

A: It is required to match the column

Q: T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm…

A:

Q: weld is called for by the small triangle on the underside of the welding symbol?

A:

Q: What may happen if the GMA welding electrode is allowedto strike the base metal outside of the…

A: given; What may happen if the GMA welding electrode is allowed to strike the base metal outside of…

Q: How is the removal of the backing strip noted on a welding symbol

A: 4992-2031R AID: 999

Q: Design the above joint using welded connection. The required length of weld is: Answer:

A:

Q: What problem must be overcome if the amperage and voltage are lowered to make a vertical weld?

A: Vertical welding:- The vertical welding is defined as a weld is applied to a vertical surface or one…

Q: On all CJP groove welds in butt joints transverse to the computed tensile stress, they

A: A groove weld is an aperture between two joint elements that enables room for the metal to be…

Q: Assuming that the quired weld size for the weld shown below using E60 welding rod (S, = 345 MPa) nd…

A:

Q: Q1/ If the weld size equal to (1.1 cm) find the Umax for figure bellow?

A: Given:-

Q: How do excessive amounts of manganese affect a weld?

A: The fabrication process is the process which is involved to build a product by mixing standardized…

Q: Describe two methods of striking an arc with an electrode

A: There are two methods of striking an arc   Scratching   Tapping