T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm length on both sides. What weld size is required to give a safety factor of 3.0 if E60 series welding is used? [Ans. 10 mm] 100 mm 18KN 75 mm Note: There are two 100 mm welds.

T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm length on both sides. What weld size is required to give a safety factor of 3.0 if E60 series welding is used? [Ans. 10 mm] 100 mm 18KN 75 mm Note: There are two 100 mm welds.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter4: Shielded Metal Arc Welding Of Plate

Section: Chapter Questions

Problem 25R: Can a tee weld be strong if the welds on both sides do not have deep penetration? Why or why not?

See similar textbooks

Related questions

Q: Superheated steam at 652 psia and 608 F is generated in an Oil-fired boiler at the rate of 100,000…

Q: 3.5 In a simple constant pressure gas turbine cycle with maximum to minimum temperature ratio ß and…

Q: 100 mm 50 mm 150 mm An orifice with a 50 mm in diameter opening is used to measure the mass flow…

Q: A polytropic process is carried out from an initial pressure of 110 kPa and volume of 5 m3 to a…

Q: A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of…

Q: T3.2.1The bracket shown below is to support a total load (equally divided between the two sides) of…

A: Given data as per the question safety factor = 3 Calculations T=F2(55+x)=30×103(55+22.5)=2.325×106…

Q: 1. a) List two jobs where scale models are used. b) List two jobs where scale drawings are used.

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Example 15.12. A steam turbine is fed with steam having an enthalpy of 3100 kJ/kg. It moves out of…

A: Introduction: The feedwater warmers are made up of tubes that carry feedwater through. Steam from…

Q: A cylinder consists of an outer tube of internal and external diameters of 16 cm and 18 cm…

A: We know that a cylinder is made up of an outer tube with internal and external diameters of 16 cm…

Q: ng upward is given by a = (4 + 0.038) m/s², rocket to reach an altitude of s = 100 m. 0. are

Q: Find pressure on the piston ?

A: Given data; Find pressure on the piston ?Diameter,d=60 cmForce,F=2000 NIt is uniformly applied

Q: power required to carry out this operation

A: Given data; Thickness,t=1 mmdiameter,d=100 mmfeed,f=1 m/minspecific cutting energy,u=6…

Q: Q3. The inclined beam is suffered by king eat (1) vollar alf). Dettimine the load at (land() and B…

A: Given: The load, P = 500 N

Q: A wooden plank x meters long has one end leaning on top of a vertical wall 1.5 m long and the other…

Q: Q2(30%) Determine the resultant of forces system shown in Figure and locate it with respect to point…

Q: An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from…

Q: le. There is coincidence between the third graduation of the ve of the graduations of the fixed…

A: Given Data : Main scale reading =10+0.5+0.5+0.5+0.5=10+2=12 mm Thimble scale reading = 0 mm Since…

Q: A CNC worktable is driven in a linear direction by a lead screw connected directly to a stepper…

Q: Air is drawn in a gas turbine unit at 15°C and 1.01 bar and pressure ratio is 7: 1. The compressor…

Q: A cyclist on a circular track of radius r = 800 ft is traveling at 27 ft/s. His speed in the…

Q: A stone is dropped from a deck above a lake strikes the water after 9 seconds. Use acceleration due…

Q: A 10-inch waterwheel were spinning by the weight of flowing water at one liter per second. If the…

A: GivenD=10inflow rate Q=1ltr/sec=0.001 m3/sh=0.5m

Q: A refrigerator used to cool a computer requires 1.2 kW of electrical power and has a COP of 1.8.…

A: Electrical power input = Power required to run compressor = Work input = 1.2 kW COP of the…

Q: Would it be possible to use a normal domestic refrigerator as a heat source for a small hot tub or…

A: Given: The whirlpool volume, V = 300 gal = 1.1356 m^3 The compressor power, W = 1 hp = 746 watt The…

Q: Problem 12-5 Determine the end moments for the built-in beam carrying central concentrated load, as…

A: Using castigliano's theorem solution, we must find the end moments for the built-in beam carrying…

Q: As a future agriculturist, is farm mechanization important? Why

Q: A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm.…

A: Answer: The length of the bar is 1.58 m.

Q: VOR can be tuned from the following places in most large body aircraft. Nav control panel MCDU…

A: following is the answer to the above problem

Q: Determine reactions in A and tension in cable as shown in figure?

Q: novel heat engine is being considered for producing work from the thermal energy contained in the…

Q: ) Determine reactions in A and tension in cable as shown in figure? 300 KN 30 kN/m 20 kN/m 4m 8m T…

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: Draw the simplified free-body diagram and below it the shear and bending moment diagrams. Show all…

A: Draw the free-body diagram of the beam.

Q: Treated Natural Gas Mixed Refrigant m M Mixed Refrigant (M) LNG

A: Introduction: In the case of dual cycle mixed the mixed refrigerant cycle, which has a low power…

Q: A sab Later, one thickness is maint oined at surfaces is in veched to. increased to 50°C. 20°C…

A: Given : To find : Temperature distribution

Q: Using appropriate sketches, draw a two-stage refrigeration system with a flash chamber. Explain…

A: Two stage refrigeration system means two stage compression refrigeration system.

Q: A 1 mm thick cylindrical tube, 100 mm in diameter, is orthogonally turned such that the entire wall…

Q: 2. Consider a regenerative vapor power cycle with one open feedwater heater. Steam enters the…

Q: A steel flask of 0.06 m³ capacity is to be used to store nitrogen at 140 bar, 20° C.The flask is to…

A: Given:P1=140 barT1=20 CV1=0.06 m3

Q: 4.4 A nylon spacing bar has the cross section shown. Knowing that the allowable stress for the grade…

Q: manufacturer lists the flow coefficient for a certain control valve as 3.5 at a flow rate of 40…

Q: If e=26.3°, calculate the minimum coefficient of static friction at A and B so that the frame's…

Q: What are the reaction forces? 122

Q: A high performance four-stroke SI engine has swept a volume of 875cm3 and a compression ratio of…

Q: Part II. 1. Herschel-Buckley Equation An unknown non-newtonian fluid underwent theology analysis.…

A: Given: To determine: Fluid behavior index, consistency coefficient, Type of non Newtonian fluid.

Q: motor vehicle with a wheel diameter of 712 mm develops 50 kW at 2,000 rpm combined efficiency of the…

Q: Convert the reading of pressure to kpa.

Q: The angular velocity vector AB -1.5 î+ 2₁+ k² a. = W 6 [ (AB) (1.52 +2²+1²) 1/2 -3.3421 +4.4561¹ +…

A: Given Data The angular velocity is:ω=6 rad/s The angular acceleration is:α=-25 rad/s2 To find: The…

Q: Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber.…

A: Given: To find: make-up water and cooling water flow rates in kg/hr

Q: Q10: Windmills slow the air and cause it to fill a larger channel as it passes through the blades.…

A: In the fluid mechanics the ratio between the mass of the fluid to the volume of that fluid is known…

Question

T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for
full 100 mm length on both sides. What weld size is required to give a safety factor of
3.0 if E60 series welding is used? [Ans. 10 mm]
100 mm
18kN
75 mm
Note: There are two 100 mm welds.
1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assume that two 1.5-mm thick steel sheets are being spot welded at a current of 4000 A and current-flow time is 0.3 s. Using electrodes 5 mm in diameter, estimate the amount of heat generated and the amount of heat required to melt the weld nugget. Use an effective resistance of 350 un. Take u= 9,7 Joule/mm Which one of the following are correct? O a. If the electrodes were 7 mm diameter, the amount of heat generated would decrease b. The amount of heat generated by the equipment is between 1600 to 1700 Joules c. The equipment has enough power to weld the steel sheets. d. The equipment does not have enough power to weld the steel sheets e. The amount of heat required is between 700 and 750 Joules
Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown below. For dynamic forces, both dynamics are synchronized, and when the force in the y-axis direction is downward, it is on the right in the x-axis direction. When the force is up, the other force is on the left. The welded part is made of 1018 HR steel, 10 mm thick. a) Safety factor for welding? b) Calculate the safety factor for the base metal. (Electrode type for question is E9010.)
The unit melting energy for a certain sheet metal is 10J/mm^3 .The thickness of each of the two sheets to be spot-welded is = mm. To achive required strength, it is desired to form a weldnugget that is =7 mm in diameter and 3.5 mm thick. The weld duration will be set at 44 sec .If the electrical resistance between the two surfaces is 144 micro-ohms and only one half the electricity generated will be used to form the weld nugget Determine the minium current level required in this operation
Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.
An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?
A bracket, as shown in figure below, is welded to a plate. The welds have the same size, and thepermissible force per mm of the weld-length is 1 kN. Calculate the lengths l1 and l2.
A mild steel ammonia receiver is a cylinder 2 m in diameter with a pressure load of 1250 kPa and a design stress of 65 MPa. The lap welding tensile strength is 450 MPa and the weld -joint efficiency is assumed to be 100%. Compute the bursting pressure of the receiver in kN/m².
A bracket to be welded into a steel channel using E-60 electrode 345 Mpa) Two welding sets are suggested as shown in Fig. (1)Based on maximum shear stress failure theory and safety factor of (2.5) (a) Find the weld size for each set. (b) Which set would you recommend A or B ?
QUESTION 20 Below is an image showing two 4 mm thick sheets joint together using double rivets. If the rivets were made of st
A GTAW operation is performed on low carbon steel, whose unit melting energy is 10.3 J/mm3. The welding voltage is 22 volts and the current is 135 amps. The heat transfer factor is 0.7 and the melting factor is 0.65. If filler metal wire of 3.5 mm diameter is added to the operation, the final weld bead is composed of 60% volume of filler and 40% volume base metal. If the travel speed in the operation is 5 mm/sec, determine (a) cross-sectional area of the weld bead, and (b) the feed rate (mm/sec) at which the filler wire must be supplied.
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)
A cylindrical air-compressor tank with an inside diameter of 50 mm is to be designed to withstand safely a working pressure of 0.86 MPa. Boiler plate with an allowable tensile stress of 76 MPa. All seams will be butt welds with an expected efficiency of 100 percent. a.) Determine the force per lineal mm of longitudinal seam, b.) Determine the required thickness “t” of wall, c.) Determine the unit stress in the circumferential seam.