why are some weld joints grooved?

Q: How much of the surface beside a weld groove must be cleaned for the AWS SENSE workmanship samples?

A: AWS stands for American Welding Society. SENSE  Schools Excelling through National Skills Standards…

Q: A fillet weld can be used to join which of the following joint types: *

A:

Q: efficiency of the joint ?

A: Given; Ratio of diameter of rivet to pitch of rivet is;  dp=0.22We have to find the tearing…

Q: What are the grooves most often used for welding on mild steel pipe

A: Single V Single U Single J Single bevel grooves

Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned

A: Fillet welding is the process of welding to weld the 2 metals at an angle or perpendicularly.

Q: What is the relationship between the degrees of freedom and the types of joints?

A: Given: Relationship between the degree of freedom and the types of joints

Q: 4. Define welding?

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: Draw the welding symbol from the following information. SINGLE J BUTT WELD CONVEX FACE SIZE 5 mm…

A: Given: Drawn the welding symbols.

Q: 6 Compare between the weld decay Attack and Knife-Line Attack.

A: There are two major corrosions that occur in steels and they are weld decay and knife-line.

Q: Why should there be a space between the plates whenmaking a fillet weld on thick plates of a tee…

A: Fillet welding refers to the process of joining two pieces of metal together when they are…

Q: 5 Which of the following appropriate methods are adopted for reducing distortion in weldments?

A: When materials are welded together, because of the uneven cooling the stresses are induced in the…

Q: Design the above joint using welded connection. The w=15mm. The required length of weld is:

A:

Q: Why should convex weld faces be avoided?

A: Excessive Convexity This discontinuity can produce a notch effect in the welded area and,…

Q: what setting needs to be adjusted before welding?

A: Setting needs to be adjusted before welding :-

Q: Which of these welds could be analyzed using the AISC Code's "kips per inch" method? (Indicate all…

A: AISC stands for American institute of steel construction.It is basically quality management system…

Q: What type of support is at joint A?

A: The joint at point A is roller.

Q: Why are all welds not inspected to the same level orstandard?

A: Information Provided: Not all welds undergo the same level or standard of inspection. Not all welds…

Q: What is the minimum acceptance criteria for porosity for visual inspection of lap welds?

A: Lap welding: When two metals are attached in a overlapping pattern on top of each other then this…

Q: Why must cast iron weld metal be ductile

A: Cast iron is the alloy of carbon and iron. Cast iron has high hardness due to presence of high…

Q: 24. Why is it important not to strike the arc outside of the weld joint?

A: Welding is a fabrication process in which two similar metals or dis similar metal are joined with…

Q: - What is mean by M24 X 2-RH 2-What is the function of a cover plate in riveted joints? 3- If a weld…

A: Given : M24 X 2-RH

Q: 1. What does the following welding symbol indicate? GTAW 100 (5) c-d b. C. d. 2. Describe the…

A: We can solve first question since the exact one is not specified. Please resubmit the question by…

Q: Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved.…

A: The cross groove joint uses balls and V-shaped grooves mostly on inner and outer races to cater the…

Q: In which of the following welded joints do both the work pieces are in the same plane? O A. Lap…

A:

Q: After the weld is set up and ready to begin, how mightthe welder want to check for freedom of…

A: Welder method for determine the degree of freedom

Q: What bead pattern is best for overhead welds?

A: Vertical up overhead smaw is best bead pattern for overhead welding. While you're in the vertical…

Q: Please give me another Welded connections sample problems and solutions as a revi

A: Q. Determine the design strength of the tension member and connection system shown below. The…

Q: What helps hold the weld in place on a 4G weld?

A: 4G weld :-  It is an overhead position used for butt welds. Welders need to hold the torch from…

Q: Why is a prototype custom fabricated before producing multiple weldments

A: Why is a prototype custom fabricated before producing multiple weldments

Q: weld is called for by the small triangle on the underside of the welding symbol?

A:

Q: Estimate the safe static load F for the weldment

A: Given: Design factor 2 Allowable shear stress 190 MPa To determine: The force applied

Q: Who is ultimately responsible for the welder’s safety?

A: Welding is a process in which a large amount of the gasses and heat released if all these are not…

Q: Q2B/ Answer any one of the following: 1. Define weld decay and how can be prevented

A:

Q: Design the above joint using welded connection. The required length of weld is: Answer:

A:

Q: Please give me some Welded connections sample problems and solutions as a review.

A:

Q: report about Soldering.

A:

Q: What problem must be overcome if the amperage and voltage are lowered to make a vertical weld?

A: Vertical welding:- The vertical welding is defined as a weld is applied to a vertical surface or one…

Q: Why is it important to make sure that an FCA welding system is set up properly if out-of-position…

A: Sparks and ultraviolet light are used in the operation of FCA. Its main job is to create…

Q: What unusual metal combination can be welded usingpercussion welding?

A: Percussion welding (PEW) is a type of resistance welding that blends dissimilar metals  together.…

Q: what items need to be turned on before welding

A: The terms to be turned on before welding : 1. Safety: This is the most important factor which should…

Q: why is the fca welding process not used for open root critical welds

A: Critical welds are the welds whose failure could be a disaster in terms of loss of property or human…

Q: Why are some joints back gouged?

A: Gouging is important for any task related to welding when the operator removes material to get a…

Q: Draw the welding symbol from the following information.      SINGLE BEVEL BUTT WELD CONCAVE FACE…

A: To Draw the welding symbol from the following information.      SINGLE BEVEL BUTT WELD CONCAVE FACE…

Q: And number of joints?

A:

Q: 9) State true or false "Electro-slag welding offers better weld properties of medium carbon steel…

A: Given problem is based on manufacturing.

Q: What will be the notation of throat length of a fillet weld

A: Given data⇒ Fillet weld Throat length