A flat belt connects pulley A, which drives a machine tool, to pulley B, which is attached to the shaft of an electric motor. The coefficients of friction are u, = 0.25 and uk = 0.20 between both pulleys and the belt. Knowing that the maximum allowable tension in the belt is 600 lb, determine the largest torque that the belt can exert on pulley A.

A flat belt connects pulley A, which drives a machine tool, to pulley B, which is attached to the shaft of an electric motor. The coefficients of friction are u, = 0.25 and uk = 0.20 between both pulleys and the belt. Knowing that the maximum allowable tension in the belt is 600 lb, determine the largest torque that the belt can exert on pulley A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flat belt connects pulley A to pulley B. The coefficients of friction are μs = 0.25 and μk = 0.20 between both pulleys and the belt. Knowing that the maximum allowable tension in the belt is 4 kN, determine the largest torque which can be exerted by the belt on pulley A. The radius of the bigger pulley A is R = 203 mm and the radius of the smaller pulley B is r = 25.4 mm. Calculate the resulting bearing force in A.
In the mechanism shown below, the distributed load W is 300 Nim and the angle 9 is 55, knowing that link AB has 1.5cmx 1.5cm cross-section
A flat belt connects pulley a, which drives a machine tool, to pulley b, which is attached to the shaft of an electric motor. the coefficients of friction are μs = 0.25 and μk = 0.20 between both pulleys and the belt. knowing that the maximum allowable tension in the belt is 600 lb, determine the largest torque that the belt can exert on pulley a
A torque of 10kN-m is to be carried by a flanged bolt coupling that consists of eight 10mm diameter steel bolts on a circle of diameter 400mm and six 10mm diameter steel bolts on a circle of diameter 300mm. Determine the number of 10mm diameter steel bolts that must be used on the 400mm bolt circle of the coupling to increase the torque capacity to 15kN-m.
A flange coupling having 180 mm bolt circle and 19 mm thick uses 12 bolts, 16 mm diameter to connect two shafts. It is used to transmit 80 Hp at 180 rpm. Determine the factor of safety in bearing if yield point in compression is 65 ksi.
The drive belt on a vintage sander transmits ½ hp to a pulley that has a diameter of d = 4 in. Knowing that the pulley rotates at 1450 rpm, determine the tension difference T1-T2 between the tight and slack sides of the belt.
Solve Prob. 4.91, assuming that the pulley rotates at a constant rate and that TB = 104 N, T'B = 84 N, and TC= 175 N.(Reference to Problem 4.91):Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by bearings at A and D . The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Knowing that when the system is at rest, the tension is 90 N in both portions of belt B and 150 N in both portions of belt C, determine the reactions at A and D . Assume that the bearing at D does not exert any axial thrust.
A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
A lubricated bolt needs an initial torque of 145 lb-ft to take the initial tension brought by the compressor withoutbreaking. Determine the initial torque needed by the bolt if the bolt was not lubricated.A. 107.85 lb-ft B.108.25 lb-ft C. 108.75 lb-ft D. 193.33 lb-ft