Block A supports a pipe column and rests as shown on wedge B . Knowing that the coefficient of static friction at all surfaces of contact is 0.25 and that θ = 45°,  determine the smallest force P required to raise block A. Determine the smallest force P for which equilibrium is maintained

Q: pin at O and the cable AB. The weight W = 7 N is attached to the free end of the cable. a) Determine…

A: Since you have asked a multi-question, thus we can provide you the solution to the first question…

Q: The cylinder shown is of weight W and radius r. Express in terms W and r the magnitude of the…

A: FBD of the cylinder: For maximum M motion impends both at A and B,

Q: A rod DE and a small cylinder are placed between two guides as shown. The rod is not to slip…

A: Draw the free body diagram of the cylinder. Here ɸB and ɸC is the shear angles of the mating…

Q: A homogeneous block of weight W rests upon the incline shown in the figure. If the coefficient of…

A: Given data as per question  coefficient of friction = 0.30 considering…

Q: Two 10-lb blocks A and B are connected by a slender rod of negligible weight. The coefficient of…

A:

Q: A band belt is used to control the speed of a flywheel as shown. Determine the magnitude of the…

A: Given Applied force = 100 N Friction coefficient = 0.25 To find Magnitude of couple acting on the…

Q: Bar AB is attached to collars that can slide on the inclined rods shown. A force P is applied at…

A:

Q: 4. The 5-kg cylinder is suspended from two equal-length cords. The end of each cord is attached to a…

A:

Q: Knowing that the coefficient of static friction between the block and the slope is 0.25 and the…

A: GIVEN :- P=55 NμS=0.25μK=0.20β=10°   SOLUTION:- Case:1 Let's assume block is moving in upward…

Q: The machine base shown has a mass of 75 kg and is fitted with skids at A and B. The coefficient of…

A:

Q: The pulley system shown is used to support and/or hoist the 200- kg block as shown. The coefficient…

A:

Q: Problem 2. The 180-lb rock climber is held in place over the edge of the cliff by his two companions…

A:

Q: The block and tackle shown are used to lower a 150-lb load. Each of the 3-in.-diameter pulleys…

A: Given, Considering Free Body diagram of First Pulley BC As friction is present between the pulley…

Q: A 6.5-m ladder AB leans against a wall as shown. Assuming that the coefficient of static friction μs…

A: Given data as per the question Length of ladder = 6.5 m coefficient of static friction at B  =0…

Q: Two slender rods of negligible weight are pin-connected at C and attached to blocks A and B, each of…

A: According to the problem, the angle θ is equal to 80o. Draw a free body diagram for the forces…

Q: The square-threaded worm gear shown has a mean radius of 2 in. and a lead of 0.5 in. The large gear…

A: Consider the diagram shown below for the larger gear, From the moment equilibrium about the center…

Q: A 40-kg packing crate must be moved to the left along the floor without tipping. Knowing that the…

A: Given, m = 40 kg μ = 0.35 Also given that, the crate is moved towards to left with tipping which…

Q: The 10-lb uniform rod AB is held in the position shown by the force P. Knowing that the coefficient…

A: μA=μB=0.20

Q: PROBLEM 3: The coefficients of friction between the block and the rail are µ, and µg. Determine the…

A:

Q: The coefficient of static frictions between the 96-lb body and the 18° wedge is 0.19. Determine the…

A: (a) To find: The magnitude and the direction of the force P. Given: The weight of the body is 96 lb.…

Q: Two slender rods of negligible weight are pin-connected at C and attached to blocks A and B, each of…

A: AC and BC are two-force membersFree body: Joint CForce triangle:  From Force triangle:…

Q: 4. The position of the machine block B is adjusted by moving the wedge A. Knowing that the…

A: A) Raising the Machine: f1 = μN1 = 0.35N1 f2 = μN2 = 0.35N2 Applying the Equilibrium Equations…

Q: shown, a man is leaning against the side of a cabinet with an unusual design. The cabinet's main…

A:

Q: A 15° wedge is forced into a saw cut to prevent binding of the circular saw. The coefficient of…

A: Given: The coefficient of static friction is μs=0.25. The magnitude of force P is P=30 lb. The…

Q: A hot-metal ladle and its contents weigh 130 kips. Knowing that the coefficient of static friction…

A: Given Data Diameter of bearings, D=16 in Radius of bearing ,R=8 in Coefficient of static friction,…

Q: A window sash weighing 10 lb is normally supported by two 5-lb sash weights. Knowing that the window…

A: Given Data Let, W is the weight of window = 10 lb T is the weight of sash = 5 lb = W/2

Q: Two slender rods of negligible weight are pin-connected at C and attached to blocks A and B , each…

A: Consider the joint C, Here, FAC is the force in the bar AC and FBC is the force in the member BC.

Q: The 20-lb block A hangs from a cable as shown. Pulley C is connected by a short link to block E ,…

A: The tension in the pulley is shown as, Ballance the forces in the vertical direction,…

Q: What weight W must be suspended through a fixed pulley shown to start motion to the left of the…

A:

Q: Block A supports a pipe column and rests as shown on wedge B . Knowing that the coefficient of…

A: Answer : Given parameters Coefficient of Friction,  μ = 0.25 Weight  = 3KN Least Force P = ?

Q: Two rods are connected by a collar at B . A couple MA with a magnitude of 15 N.m is applied to rod…

A: Given data MA=15 N·mμ=0.3AC=325 mmABx=100 mmABy=200 mm

Q: Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static…

A: Given:-θ=45°μ=0.30To find:-Smallest force P

Q: A 6.5-m ladder AB leans against a wall as shown. Assuming that the coefficient of static friction μs…

A: Given: The length of the ladder is L=6.5 m. The coefficient of static friction is μs. The…

Q: Solve Prob. 8.19 assuming that the coefficients of friction at B are zero.(Reference to Problem…

A: Free body diagram

Q: Knowing that the coefficient of static friction between the tires and the road is 0.80 for the car…

A: Write the given data with suitable variables. μ=0.8v=360 in/ss=240 ing=386.08 in/s2

Q: What weight W must be suspended through the fixed pulley shown to start motion to the left of the…

A:

Q: A slender steel rod with a length of 225 mm is placed inside a pipe as shown. Knowing that the…

A: Given Length of the pipe = 225 mm Diameter of the pipe = 75 mm Coefficient of friction = 0.2 To find…

Q: Solve Prob. 8.93 assuming that the normal force per unit area between the disk and the floor varies…

A: Given Weight of the floor polisher,  Coefficient of kinetic friction,  Draw the diagram of the…

Q: The block and tackle shown are used to raise a 150-lb load. Each of the 3-in.-diameter pulleys…

A: According to principle of Kinematics, The total Upward and Downward forces are zero.

Q: The double pulley shown is attached to a 10-mm-radius shaft that fits loosely in a fixed bearing.…

A:

Q: A 6.5-m ladder AB leans against a wall as shown. Assuming that the coefficient of static friction μs…

A:

Q: What weight W must be suspended through the fixed pulley shown to start motion to the left of the…

A: Given data The weight of the wedge A is WA=1500 N The weight of the wedge B is WB=3000 N The…

Q: The slender, uniform bar BC with a mass of 6 kg rests on the center of the 300x200 mm block of mass…

A:

Q: Knowing that the coefficient of static friction between the block attached to rod ACE and the…

A: To find: The largest and smallest force. Given: The length of the bar is l=0.2 m. The angle is…

Q: 3. (a) A 15 kg rod AB of length 2.5 m and a uniform cross section, is held in equilibrium as shown…

A: Angle of static friction(ϕs)⇒ It is the angle made by contact force with normal reaction when the…