A flat plate of width 1 m and length 0.22 m is maintained at a temperature of 32°C. Ambient fluid at 22°C flows across the top of the plate in parallel flow. Determine the average heat transfer coefficient, the convection heat transfer rate from the top of the plate, and the drag force on the plate. The fluid is water flowing at a velocity of 0.5 m/s. Assume the critical Reynolds number is 5x105. Determine the average heat transfer coefficient, in W/m².K. i 116.7 W/m².K h₂: = Determine the convection heat transfer rate, in W, from the top of the plate. 9 = i 256.74 W Determine the drag force, in N, on the plate. F = i 0.00119 N

A flat plate of width 1 m and length 0.22 m is maintained at a temperature of 32°C. Ambient fluid at 22°C flows across the top of the plate in parallel flow. Determine the average heat transfer coefficient, the convection heat transfer rate from the top of the plate, and the drag force on the plate. The fluid is water flowing at a velocity of 0.5 m/s. Assume the critical Reynolds number is 5x105. Determine the average heat transfer coefficient, in W/m².K. i 116.7 W/m².K h₂: = Determine the convection heat transfer rate, in W, from the top of the plate. 9 = i 256.74 W Determine the drag force, in N, on the plate. F = i 0.00119 N

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.22P

See similar textbooks

Similar questions

Air at 1 atm with a velocity of 4 m/s and a temperature of 50oC flows over a flat plate that is at a uniform temperature of 100oC. The plate has a length of 0.20 m and a width of 0.1 m. a) What is the average heat transfer coefficient? b) What is the heat transfer rate from plate to the air? c)What is the average friction coefficient and the drag force ? d)What is the heat transfer coefficient at x=0.15 m ?
Calculate the rate at which the average friction coefficient, friction force and heat transfer rate will change if the free flow rate of the turbulent air flowing parallel to the plate over a smooth plate is doubled. Does the result change for constant temperature and constant heat flux conditions; Please evaluate.
Air at 60°F flows over a 10-ft-long flat plate at 7 ft/s. Determine the local friction and heat transfer coefficients at intervals of 1 ft, and plot the results against the distance from the leading edge.
A coated sheet is being dried with hot air blowing in cross flow on the sheet surface. The surface temperature of the sheet is constant at 90°C, while the air velocity and temperature are 0.3 m/s and 110°C, respectively. The length of the sheet subjected to the blowing hot air is 1 m long. Determine the convection heat transfer coefficient and the heat flux added to the sheet surface. Treat the coated sheet as a vertical plate in cross flow.
A 1.2-in-outer-diameter pipe is to span across a river at a 140-ft-wide section while being completely immersed in water. The average flow velocity of the water is 10 ft/s, and its temperature is 70°F. Determine the drag force exerted on the pipe by the river.
Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate, placed on ground, where there is an unheated starting length of 1 m. The air stream has a temperature of 20 °C and the heated section of the flat plate is maintained at a constant temperature of 80 °C. Determine the local heat transfer coefficient at trailing edge and average convection heat transfer coefficient for the heated section. Also calculate the heat loss by convection. Determine the average friction coefficient and wall shear stress and drag force.
Water at 60 ⁰C and velocity of 2 cm/s flows over a 5 m long flat plate which is maintained at a temperature of 20 ⁰C. Determine the total drag force and rate of heat transfer per unit width of the plate
What are the three layers within turbulent flow? In which layer is the velocity smallest and in which layer is the turbulent portion of the shear stress dominant?
Consider laminar flow over a flat plate. How does the local friction coefficient change with position?
Consider a bullet piercing through calm air during a short time interval in which the bullet’s speed is nearly constant. Determine if the time-averaged airflow over the bullet during its flight is one-, two-, or three-dimensional
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C . The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 °C , what is the overall heat transfer at the laminar section?
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.