A flexible pavement is designed to last 10 years to withstand truck traffic that consists only of trucks with two 18-kip single axles. The pavement is designed for a soil CBR of 10, an initial PSI of 5.0, a TSI of 2.5, an overall standard deviation of 0.40 and a reliability of 90%, and the structural number was determined to be 6. On one section of this roadway, beneath an underpass, an engineer uses an 8-inch rigid pavement in an attempt to have it last longer before resurfacing. How many years will this rigid-pavement section last? (Given the same traffic conditions, modulus of rupture = 800 lb/in2, modulus of elasticity = 5,000,000 lb/in2, load transfer coefficient of 3.0 and drainage coefficient of 1.0.).

A flexible pavement is designed to last 10 years to withstand truck traffic that consists only of trucks with two 18-kip single axles. The pavement is designed for a soil CBR of 10, an initial PSI of 5.0, a TSI of 2.5, an overall standard deviation of 0.40 and a reliability of 90%, and the structural number was determined to be 6. On one section of this roadway, beneath an underpass, an engineer uses an 8-inch rigid pavement in an attempt to have it last longer before resurfacing. How many years will this rigid-pavement section last? (Given the same traffic conditions, modulus of rupture = 800 lb/in2, modulus of elasticity = 5,000,000 lb/in2, load transfer coefficient of 3.0 and drainage coefficient of 1.0.).

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter19: Design Of Flexible Highway Pavements

Section: Chapter Questions

Problem 13P: Repeat Problem 19-7 using two different depths of untreated aggregate bases of 6 in. and 12 in....

See similar textbooks

Similar questions

Repeat Problem 19-7 using two different depths of untreated aggregate bases of 6 in. and 12 in. Highway contractors in your area can furnish rates for providing and properly laying an asphalt concrete surface and untreated granular base. Assume a structural coefficient of 0.12 for the base course. If these rates are available, determine the cost for constructing the different pavement designs if the highway section is 5 miles long and the lane width is 12 ft. Which design will you select for construction?
Pavement Design and Analysis - Design a HMA pavement structure for a 6-lane divided urban highway using the AASHTO method to accommodate the traffic loads and conditions as follows. Give two alternative layer thickness combinations.
A northbound direction on an interstate highway consists of four lanes of flexible pavement. It is conservatively designed with a 10-inch sand-mix asphaltic surface, 10-crushed stone base, and a 10-inch crushed-stone subbase (all drainage coefficients are 1.0). The subgrade CBR is 3, the overall standard deviation is 0.4, and the reliability is 95%. The initial PSI is 4.6 and the final PSI is 2.5. Daily total northbound road traffic consists of 51,000 cars (each with two 2-kip single axles), 840 buses (each with two 20-kip single axles), and 1,000 heavy vehicles (each with one 12-kip single axle and two 34-kip tandem axles). How many years was this pavement designed to last?
Determine the required structure number of the pavement based on the following information: . . ESAL= 5 million Reliability = 99% Standard deviation = 0.45 • Pi = 4.5, Pt = 2.5 . Subgrade Mr=9,000psi
A flexible pavement has a structural number of 3.8 (all drainage coefficients are equal to 1.0). The initial PSI is 4.7 and the terminal serviceability is 2.5. The soil has a CBR of 9. The overall standard deviation is 0.40 and the reliability is 95%. The pavement is currently designed for 1800 equivalent 18-kip single-axle loads per day. If the number of 18-kip single-axle loads were to increase by 30%, by how many years would the pavement design life be reduced?
The AADTT of a 2-way (2-lane each way) highway is 10,000. The directional distribution may vary between 45 and 55% depending on season. The lane distribution may vary between 60 and 75%. The driving lane always carries more loads compared to the passing lane. The growth factor for the pavement is 3.5%. Based on the above information, calculate the design AADTT for the driving lane if the pavement service life is 20 years.
section of a two-lane rural highway is to be realigned and replaced by a four-lane highway with a full-depth asphalt pavement. Consists of 40% trucks. If classification studies have shown that the truck factor can be taken as 0.45, design a suitable flexible pavement using the 1993 AASHTO procedure if the AADT on the design lane during the first year of operation is 1000. It is expected that construction will be completed five years from now, and pi =4.5 and pt = 2.5. Growth rate = 4%. Design life = 20 years. The pavement structure will be exposed to moisture levels approaching saturation 20% of the time, and it will take about one week for drainage of water. Effective CBR of the subgrade material is 7. CBR of the base and subbase are 70 (Mr=30000 lb/in2 ) and 22 (Mr=13500 lb/in2 ), respectively, and Mr for the asphalt mixture, 400,000 lb/in2 .
answer with complete solution. Asap 1. determine the safe thickness of rigid pavement if the wheel load is 85 kN and f'c = 32 MPa
Subject : Transportation Engineering Read the question carefully and give me right solution according to the question. Note: solve by using 45-deg cone pressure distribution method only The maximum wheel load that the pavement could carry is 120 kN. If the contact radius of the wheel is assumed to be 250 mm, and subgrade bearing capacity is equivalent to 0.24 Megapascals, calculate the subgrade layer thickness of the flexible pavement in mm using the 45-deg cone pressure distribution method.
Determine the safe thickness of rigid pavement if the wheel load is 85 kN and f'c=32 MPa.
A flexible pavement was designed for the following daily traffic with a 12-year design life: 1300 single axles at 8,000 lb each, 900 tandem axles at 15,000 lb each, 20 single axles at 40,000 lb each, and 200 tandem axles at 40,000 lb each. The highway was designed with 4 inches of hot-mix asphalt (HMA) wearing surface, 4 inches of hot-mix asphaltic base, and 8 inches of crushed stone subbase. The reliability was 70%, overall standard deviation was 0.5, ¨PSI was 2.0 (with a TSI of 2.5), and all drainage coefficients were 1.0. What was the soil resilient modulus of the subgrade used in design?
2 Describe the basic types of highway concrete pavements and give the conditions underwhich each type will be constructed