A flexible pavement is known to have a structural number of 4.0 and a soil resilient modulus of 10,000 psi. If a pavement structure is to be designed for a life of 15 years, a reliability of 95% and an overall standard deviation of 0.35, how many passes of a design vehicle with a 18,000 lb single axle and a 34,000 lb tandem axle can be driven on the pavement per day?

A flexible pavement is known to have a structural number of 4.0 and a soil resilient modulus of 10,000 psi. If a pavement structure is to be designed for a life of 15 years, a reliability of 95% and an overall standard deviation of 0.35, how many passes of a design vehicle with a 18,000 lb single axle and a 34,000 lb tandem axle can be driven on the pavement per day?

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter21: Pavement Management

Section: Chapter Questions

Problem 4P

See similar textbooks

Similar questions

Repeat Problem 19-7 using two different depths of untreated aggregate bases of 6 in. and 12 in. Highway contractors in your area can furnish rates for providing and properly laying an asphalt concrete surface and untreated granular base. Assume a structural coefficient of 0.12 for the base course. If these rates are available, determine the cost for constructing the different pavement designs if the highway section is 5 miles long and the lane width is 12 ft. Which design will you select for construction?
i need an answer immediately thank you Design the thickness of a pavement to carry a wheel load of 52kN based on the following conditions and type of pavement. 3. A flexible pavement with an allowable subgrade pressure of 0.14MPa and the max. tire pressure equal to 0.52MPa. This pressure is assumed to be uniformly distributed over the area of tire contact on the roadway according to the principle of cone pressure distribution.
A flexible pavement is designed to last 10 years to withstand truck traffic that consists only of trucks with two 18-kip single axles. The pavement is designed for a soil CBR of 10, an initial PSI of 5.0, a TSI of 2.5, an overall standard deviation of 0.40 and a reliability of 90%, and the structural number was determined to be 6. On one section of this roadway, beneath an underpass, an engineer uses an 8-inch rigid pavement in an attempt to have it last longer before resurfacing. How many years will this rigid-pavement section last? (Given the same traffic conditions, modulus of rupture = 800 lb/in2, modulus of elasticity = 5,000,000 lb/in2, load transfer coefficient of 3.0 and drainage coefficient of 1.0.).
Discuss various tests used for the quality of bitumen used in flexible pavements Subject. Transportation engineering.
A dual wheel having a load per tire of 5000 Ib, 70 psi pressure and μ = 0.5. Calculate thetotal pavement deflections due to the dual wheel by one-layer theory at the followingradial distances from the centerline of one tire: r=0, 3.5,10.5. (Use Pavement Thickness= 8in).
A dual wheel having a load per tire of 4000 Ib, 80 psi pressure and μ = 0.5. Calculate thetotal pavement deflections due to the dual wheel by two layer theory at the followingradial distances from the centerline of one tire: r=0, 7,14. Assume that E1 = 10 E2
A flexible pavement is constructed with 4 inches of hot-mix asphalt wearing surface, 10 inches soil cement base and 10 inches crushed stone subbase. The subgrade has a soil resilient modulus of 12,000 lb/in2, M2 = 1.5 and M3=1.127 for the materials of the pavement structure. The overall standard deviation is 0.5, the initial PSI = 5.0 and the terminal serviceability index (TSI) is 2.5. The daily traffic has 3000 cars, 1000 trucks and 500 trailers. The axle weights are: How long in years would the pavement last if R = 98% ? (Final answer to 2 decimal places)