Q8 Beta =111Please provide justified answer asap to get a upvote Question 8A force Q (= 6B kN) is applied through the handle of the rigid steel lever (ABCDE), causing the lever(attached to three metal bars made of steel, bronze, and aluminum of different lengths and diameters asindicated in Fig. 8 to rotate about the pin support at A.BoltFSteel barBronze barDiameter ds = 2B mmDiameter dbrLs =Pin A= B mmLCD10ß mmLAB=30ß mmE=10ß mmBCALeverLDELalAluminium barDiameter dal= 40ß mm= 6B mmLBCLbr == 3ß mm= 20ß mm5B mmQ = 6B kNB = Student's serial5B = 5 times BCS Scanned with CamScanner= 30° Fig. 8Use: Diameter of steel bolt in pin A = B mmModulus of elasticity: Etel = 210 GPa, Eronze = 100 GPa, Eatuminum = 70 GPaDetermine:Deformations, strains, stresses, and forces in steel (DF), aluminum (BH), and bronze (CG)barsReaction and its direction at pin A as well as shear stress in the bolt in pin A at double shearBefore the application of load P, if there is a gap of Lal/300 between the bearing support at Band the aluminum bar, write the compatibility conditions.CS Scanned with CamScanner

Answered: Image /qna-images/answer/c4cbf3eb-4cf4-4f9a-b52b-8e4f635d7082.jpg

A force Q (= 6B kN) is applied through the handle of the rigid steel lever (ABCDE), causing the lever (attached to three metal bars made of steel, bronze, and aluminum of different lengths and diameters as indicated in Fig. 8 to rotate about the pin support at A.

A force Q (= 6B kN) is applied through the handle of the rigid steel lever (ABCDE), causing the lever (attached to three metal bars made of steel, bronze, and aluminum of different lengths and diameters as indicated in Fig. 8 to rotate about the pin support at A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A borehole drilling machine with a vertical shaft of 60 mm diameter is 500 mm long and is supported in long bearings at its top end. The shaft has Youngs modulus of E = 110 GN/m2. A disc of mass 40 kg is attached to the center of the shaft. The center of the disc is 0.25 mm from the geometric axis of the shaft. Neglecting any increase in stiffness due to the attachment of the disc to the shaft, calculate: 1.1. The critical speed of rotation. 1.2. The maximum bending stress when the shaft is rotating at 80% of the criticals peed.
A hand cranking lever, as shown in Figure 6 below, is used to start a truck engine byapplying a force F = 400 N. The material of the cranking lever has a yield strength = 320 MPa;Ultimate tensile strength = 500 MPa; Young’s modulus = 205 GPa; Modulus of rigidity = 84 GPaand poisson’s ratio = 0.3. Assuming factor of safety to be 4 based on yield strength, design thediameter of the lever at section X-X near the guide bush using: a) Maximum distortion energytheory; and b) Maximum shear stress theory.
Question 5 The nose wheel assembly of an aircraft has axle shaft which is 150 mm long. The shaft has a diameter D1 of 30 mm for the section AB, which is connected to the arm. Section BC of the shaft that is connected to the wheel has diameter D2 of 25 mm. Sections AB and BC of the shaft have mass moments of inertia of 80 kgm2 and 60 kgm2, respectively. If the modulus of rigidity of the shaft material is 80 GN/m, calculate the natural frequency of torsional vibration of the system.
A steel shaft 100mm in diameter is loaded and support in shaft bearing 0.4m apart. The shaft carries three loads: first mass 12kg at the centre, second mass 10kg at a distance 0.12m from the left bearing and third mass of 7kg at a distance 0.09m from the right bearing. Find the value of the critical speed by using Dunker ley’s method if E = 2X1011N/m2.
The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi
A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be driven by vee belts through a pulley. The combined tensions of the belt apply and the weight of the pulley assembly applies a force of 5.4kN and 900N respectively. The shaft has a diameter of 32mm. Bearing A at the top supports the shaft radially whereas bearing B at the bottom supports the shaft axially and radially. Two deep groove ball bearings have been selected for this application. The models of the bearings are SKF 6305 and SKF 6205 for bearing A and B respectively. a) What are the forces at bearing A and B? b) Paste a screenshot of the graph showing the distribution of the forces in the shaft. c) From the report, find the static load capacity for: Bearing A Bearing B
A compound shaft supports several pulleys. Segments (1) and (4) are solid 21-mm-diameter steel [G = 61 GPa] shafts. Segments (2) and (3) are solid 50-mm-diameter steel shafts. The bearings shown allow the shaft to turn freely. Assume L1=745 mm, L2=400 mm, L3=725 mm, L4=515 mm, TA=130 N-m, TB=2015 N-m, TC=1540 N-m, TD=580 N-m, TE=235 N-m.(a) Determine the maximum absolute value of the shear stress in the compound shaft.(b) Determine the rotation angle of pulley D with respect to pulley B.(c) Determine the rotation angle of pulley E with respect to pulley A.
A polyamide A-3 flat belt 6 in wide is used to transmit 15 hp under light shock conditions where Ks= 1.25, and a factor of safety equal to or greater than 1.1 is appropriate. The pulley rotational axesare parallel and in the horizontal plane. The shafts are 8 ft apart. The 6-in driving pulley rotates at1750 rev/min in such a way that the loose side is on top. The driven pulley is 18 in in diameter. Thecoefficient of friction is 0.8. Analyze the centrifugal tension Fc and the torque T.?
A bearing is subjected to a radial force of 8kN and a thrust force of 3 kN. Thevalues of X and Y factors are 0.56 and 1.5 respectively. The shaft rotates at 1200 RPM. The diameter of the shaft is 75mm and Bearing no. 6315 (C= 112000N) is selected for this application. Estimate the life of this bearing with 90% reliability.
A bearing is subjected to a radial force of 8kN and a thrust force of 3 kN. The values of X and Y factors are 0.56 and 1.5 respectively. The shaft rotates at 1200 RPM. The diameter of the shaft is 75mm and Bearing no. 6315 (C= 112000N) is selected for this application. Estimate the life of this bearing with 90% reliability. Follow the methodologies in solving the problem; Given : Required: Schematic Diagram: Solution:
A spring (squared and ground) having a pitch 0.75 inch has a mean diameter of 1.5in and a wire diameter of 0.25in. After applying a certain load, the spring deflects 0.5in with a corresponding stress of 30.75 ksi. The spring is to be made of tempered steel wire having a shear modulus of 12 million psi.
Two identical ball bearings Pand Q are operating at loads 30 kN and 45 kN respectively. The ratio of the life of bearing P to the life of bearing Qis