3. (a) Calculate the range of mass flow rates of water at 20°C for which the turbine meter of following figure would be within +0.5 percent. (b) Also, determine a flow coefficient for this fluid in terms of cycles per kilogram. 1,100 1,090 K-500 1,080 1,070 1,060 10 20 40 60 80 100 200 400 600 800 1,000 For water: kg p = 1000 m² v = 0.1 x 10-5

3. (a) Calculate the range of mass flow rates of water at 20°C for which the turbine meter of following figure would be within +0.5 percent. (b) Also, determine a flow coefficient for this fluid in terms of cycles per kilogram. 1,100 1,090 K-500 1,080 1,070 1,060 10 20 40 60 80 100 200 400 600 800 1,000 For water: kg p = 1000 m² v = 0.1 x 10-5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0il with p = 876 kg/m³ and u = 0.24 kg/m-s is flow- ing through a 1.5-cm-diameter pipe that discharges into the atmosphere at 88 kPa. The absolute pressure 15 m before the exit is measured to be 135 kPa. Determine the flow rate of oil through the pipe if the pipe is (a) horizontal, (b). inclined 8° upward from the horizontal, and (c) inclined 8° downward from the horizontal.
Specify the pipe required to carry 272.200 kg of steam per hr at 87.9 kg/cm^2 ga, 538 °C, with velocity approximately 3050 m/min
Air fl ows adiabatically in a 3-cm-diameter duct, withf 5 0.018. At the entrance, T1 = 323 K, p1 =200 kPa, andV1 = 72 m/s. (a) What is the mass fl ow? (b) For what tubelength will the fl ow choke? (c) If the tube length is increasedto 112 m, with the same inlet pressure and temperature,what will be the new mass fl ow?
A centrifugal pump is required to deliver 50 liters of water per second to a height or 30 m through a 100 m long pipe of 15 cm diameter. The inlet losses in the suction pipe are estimated to be 0.35 m. Assuming an overall efficiency of 70 percent and taking Darcy’s friction coefficient of 0.015 for the pipeline, determine the power, in kW, required to drive the pump.
A fan draws 1.42 m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan mechanical is 70% and air is measured at 25 0C and 760 mmHg. Using p water formulaPw=
A pump draws 30-°C water at 0.5 liters per second from a pressurized tank where the air pressure above the water is 1.1 atm (abs) . The required NPSH of the pump is 8.2 m. The suction pipe has a diameter of 4 cm, total length of 5.2 m, and friction factor of 0.005. If the pump has a suction lift of 3.8 m, will cavitation occur? Use the properties of sat. liquid water at 30°C.
What are the primary differences between fans, blowers, and compressors? Discuss in terms of pressure rise and volume flow rate.
Argon gas enters a constant cross-sectional area duct at Ma1 = 0.2, P1 = 320 kPa, and T1 = 400 K at a rate of 0.85 kg/s. Disregarding frictional losses, determine the highest rate of heat transfer to the argon without reducing the mass flow rate.
Air enters a fan through a duct at a velocity of 6.5 m/s and an inlet staticpressure of 2.5 cm H2O less than atmospheric pressure. The air leaves the fan through aduct at a velocity of 11.5 m/s and a discharge static pressure of 7.62 cm H2O above theatmospheric pressure. If the specific weight of air is 1.20 kg/m3 and the fan delivers 9.45m3/s, determine the fan theoretical power and the fan efficiency when the power input tothe fan is 13.75 kW at the coupling?
Assuming the clearance is negligible for a single stage compressor with the followingdata.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1. What is the power input to the compressor if compression is isentropic in kW to 3 decimal places? 2. What is the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal?
A hose of diameter 3 cm is used to drain a very large tank filled with water (=1000 kg/m3). The hose is draped over the side of the tank so the water is siphoned out. If the hose discharge is 1 m below the surface of the water, estimate the discharged mass flow rate in kg/s? A siphon implies a continuous liquid leg from the water in the tank up the siphon at point 2, the highest elevation, and down to the discharge at point 3. Assume that alpha=1, the discharge at point 3 as well as the tank are both open to the atmosphere and shaft work and frictional losses are ignored. 2.Based on your solution, how can you drain the tank faster?
Air flows steadily and isentroplcally into an aircraft inlet at a rnass flow rateof 100 kgs·1• At a section where the cross-sectional area is 0.5 m2 , thetemperature and pressure are 200 K and 20 kPa, respectively. Determinethe velocity, pressure and cross-sectional area at a downstream sectionwhere the temperature is 350 K. Sketch the flow passage, and show the ·process on a T-s diagram