Please Full solution with all the steps. BIG and clear Handwriting. Thank you Problem B-8–7A free vibration of the mechanical system shown in Figure 8–27(a) indicates that theamplitude of vibration decreases to 25% of the value at = t, after four consecutivecycles of motion, as Figure 8-27(b) shows. Determine the viscous-friction coefficient bof the system if m = 1 kg and k = 500 N/m.X4 = 0.25 x,bm(a)(b)Figure 8-27 (a) Mechanical system: (b) portion of a free-vibration curve.

Answered: Image /qna-images/answer/2b207320-7580-4957-917b-44833474b064.jpg

A free vibration of the mechanical system shown in Figure 8-27(a) indicates that the amplitude of vibration decreases to 25% of the value at = 1, after four consecutive cycles of motion, as Figure 8-27(b) shows. Determine the viscous-friction coefficient b of the system if m = 1 kg and k = 500 N/m. * = 0.25 x, (a) (b)

A free vibration of the mechanical system shown in Figure 8-27(a) indicates that the amplitude of vibration decreases to 25% of the value at = 1, after four consecutive cycles of motion, as Figure 8-27(b) shows. Determine the viscous-friction coefficient b of the system if m = 1 kg and k = 500 N/m. * = 0.25 x, (a) (b)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

..... A journal bearing for a pump has the following properties: Diametral clearance ratio = 0.0013 mm Diameter of journal = 90 mm Length of bearing = 160 mm Speed of journal = 900 rpm Lubricant viscosity = 0.02 kg/m-s Lubricant temperature = 60°C Ambient temperature = 15°C Bearing pressure in pump = 1.2 MPa Heat dissipation coefficient = 1,250 W/m2-°C Determine the amount of cooling (Qg-Qd) required in W.
The cylinder bore diameter of a double-acting reciprocating pump is 170 mm and its stroke is 370 mm. The pump runs at 55 rpm and lifts water through a height of 26 m. The delivery pipe is 23.5 m long and 113 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 13 liters/s. Assume the weight density of water is 9810 N/m3 (i)Theoretical discharge in liter/s (ii) the theoretical power required to run the pump in kW (iii) the percentage of slip (iv) the coefficient of discharge.
Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch.
A 360° journal bearing is 3 in. long and carries a 4 in. diameter shaft with a radial clearance of 0.0025 in. The shaft supports a radial load of 1000 lbs. and a speed of 500 rpm. The operating temperature for the bearing is 140°F and SAE-20 oil is used for bearing lubrication. For these conditions, evaluate the following by Petroff’s equation: 1. Friction coefficient for the bearing. 2. Heat energy lost due to friction in the bearing, in horsepower.
For a single acting reciprocating pump, piston diameter is 150 mm, stroke length is 300 mm, and rotational speed is 50 r.p.m. The pump is required to lift water to a height of 18 m. Determine the theoretical discharge. If the actual discharge is 4.0 lit./sec, and the mechanical efficiency is 80% determine the volumetric efficiency, slip, theoretical power and the actual power required.
The venturi nozzle in the airflow experiment measures a static pressure of 7 psf (lb/ft2 ) before the nozzle and a static pressure of 2 psf after the nozzle. If the Reynolds Number of the flow is 5.7E+04, gc = 32.17 lmm-ft/lbf -s2 , ρ = 0.075 lbm/f t3 Dpipe = 5 in, and Dventuri = 2.74 in, find the flow rate in the pipe. Present answer in cfm.
You are asked to design a plain surface journal bearing to carry a steady radial load of 5.75 kN while the shaft rotates at 950 rpm. The shaft stress analysis determines that an acceptable nominal diameter of the journal is 62.5-mm and an l/d ratio is 1. The shaft is part of a machine requiring good precision. So a minimum radial clearance cmin= 0.040 mm seems appropriate. We shall use SAE 30 oil as a lubricant, at an inlet temperature of 45 oC. Analyze the hypothetical bearing,a) Determine the operating temperature Tave, and operating viscosity μave. b) Determine the minimum film thickness, ho, temperature rise of the lubricant, ΔTC, the total oil flow, Q, and side flow Qs in [mm3/s], the maximum film pressure Pmaxdeveloped in [MPa]. c) Determine the power loss, Hloss in [W], friction torque, Tf in [N-m] d) For minimum radial clearances, perform a design assessment using Trumpler’s criteria.
In some damping systems, a circular disk immersed in oil is used as a damper as shown in the figure. Show that the damping torque is proportional to angular speed in accordance with the relation Tdamping = Cω. Find the expression for C neglecting tip effects
A radial plain bearing has a diameter of 60 mm and a width of 60 mm. Journal rotation speed 600rpm; radial load acting on the bearing is 3.5 kN, the inlet temperature of the SAE 20 oil used is 30 C andSince r / c = 1000;a-) The increase in the temperature of the oil and its average temperature,b-) Minimum oil film thickness, angular position and eccentricity ratio,c-) Loss of power in the bed,d-) Side leaks and total oil flow,e-) Max. oil film pressure.
A. What is the coefficient of friction for a sphere of radius 0.37 um? (the viscosity of water is 10-3 Pa.s) B. What would be the expected value of ¨d¨ from Einstein's relation? Compare the expected value with the value obtained experimentally.
BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 6 - 9
MECHANICAL VIBRATIONS ANSWER 3.4 with regards to problem 3.1