A full-bridge inverter has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Vdc=100 V, R equals to 10 Ohm, and L equals 25 mH. The average current in the dc source is. Select one: O a. 52 A O b. None of the above O c. 4.41 A O d. 300 A

A full-bridge inverter has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Vdc=100 V, R equals to 10 Ohm, and L equals 25 mH. The average current in the dc source is. Select one: O a. 52 A O b. None of the above O c. 4.41 A O d. 300 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4) A single phase full bridge inverter will be used to generate 50 Hz square wave voltage. Inverter the input voltage is 400 V and the load consists of inductance and resistance connected in series. (R=10Ω, L=31.83 mH) a) Draw the circuit b) Plot the load current, showing the load voltage and semiconductor currents. c) Load voltage is effective calculate the value d) Calculate the effective value of the main harmonic of the load current. e) Calculate the average load current. f) Find the THD of the load voltage
Q1) The square-wave inverter has a dc input of 150 V and supplies a series RL load with R-20 Ω and L = 40 mH.(a) Determine an expression for steady state load current.(b) Sketch the load current and indicate the time intervals when each switch component (Q1, D1:.. Q4, D4) is conducting.(c) Determine the peak current in each switch component.(d) What is the maximum voltage across each switch?
1. A single phase half-bridge inverter, connected to 230V dc source, feeds a resistive load of 10Ω. Determine (a) fundamental rms output voltage (b) total output power and fundamental frequency power (c) average and peak currents of switches (d) input pf. 2. Discuss 1200 mode of conduction for a 3ph-phase VSI. Also, derive the expression for the outputvoltage and draw waveforms for phase voltages, line voltages and voltage across one switch.
Design a series inverter circuit for operation in the frequency range 50Hz to 90 Hz. The load resistance may vary from 20 Ohm to 80 Ohm. :Thepeak load current is limited to 4 A and the supply voltage is 120 V
In a half wave bridge inverter circuit, the power delivered to the load by each source is given by a. VsIs b. 4VsIs c. 2VsIs d. VsIs/2
A single-phase full bridge inverter is operated from a 48V battery and issupplying power to a resistive load of 10 Ω. Determine:(i) The fundamental output voltage and first five harmonics.(ii) RMS value by direct integration method and harmonic summationmethod.(iii) Output rms power and output fundamental power.
The single-phase half-bridge inverter has a resistive load of R = 2.4Ω and the DCinput voltage is 48V. Determine:1- the rms output voltage at the fundamental frequency2- fundamental displacement factor .3- fundamental power , drown from each source .4- fundamental load power .5- total power drown from each source .6- total load power .
A DC link inverter has an AC rms line input of 600 V, 50Hz. The inverter load is a balanced star connection of 195Ω resistors.Determine load current and power for a converter firing angle delay ofa) Determine load current, voltage and power for a converter firing angle delay of 12.5 degrees.b) Determine load current, voltage and power for a converter firing angle delay of 62 degrees.
A basic inverter with unidirectional switches is connected to a resistive load. The peak supply current is 50 A, then the peak transistor and load currents are respectively: Select one: a. 25 A, 50 A b. 25 A, 25 A c. 50A,50A d. 50 A, 25 A e. None of these
Apply inverter parameter analysis equations to solve the followings for Single phase full bridge inverter. Asume inverter is used for home application to drive resistive load of ‘A’ ohm with DC battery of 60V as input. (a) Required output power (b) Average current across each transistor (c) Total harmonic distortion THD (d) Harmonics & distortion factor of 5th harmonic and (e) Draw its complete diagram Also here A= 4
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50 Hz on the serial RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma -0.9 and frequency modulation rate mf -19. The resistance of the series RL load is 15 OHM and the coil inductance is 40 mH. a) What is the power drawn by the load resistor?b) What is the total harmonic distortion value (THD) of the load current?
In a full-bridge single-phase inverter with an input voltage of 200V and a switchingfrequency of 4kHz, the power of a 16Ω load is controlled by the method of a gappedsquare wave control. Ignoring the circuit losses, answer the following questions A) Find the nominal (the maximum) power and current of the load B) Find the duty ratio to get half of the nominal voltage C) Find the duty ratio to get a quarter of the nominal power D) Find the average value and effective value of BJT current for the case of item-e