A full wave rectifier circuit is fed with from a transformer having a center tapped secondary winding . The rms voltage from either end of the secondary to the center tap is 30V . If the diode forward resistance is 2 Ω and that of the half secondary is 8 Ω for a load of 1 kΩ . Calculate the Efficiency of rectification and power delivered to the load.

A full wave rectifier circuit is fed with from a transformer having a center tapped secondary winding . The rms voltage from either end of the secondary to the center tap is 30V . If the diode forward resistance is 2 Ω and that of the half secondary is 8 Ω for a load of 1 kΩ . Calculate the Efficiency of rectification and power delivered to the load.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
What is the difference between a diode and rectifier?
Design rectifier circuits to provide an output of 100 VDC using:a) Half wave rectifierb) Center-tapped Full wave rectifier For each circuit, calculate the diode PIV ratings and the transformer turns ratio (secondary to primary), if power is taken from the 220 V line AC supply.
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
Design rectifier circuits to provide an output of 100 VDC using:a) Half wave rectifierb) Center-tapped Full wave rectifier For each circuit, calculate the diode PIV ratings and the transformer turns ratio (secondary to primary), if power is taken from the 220 V line AC supply.Use Silicon diodes.
Design a bridge rectifier circuit to provide an output of 100 VDC. Calculate the diodes PIV rating and the transformer’s turns ratio, if power is taken from the 120 V line AC supply
A 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz for 10 ohm and 1.5 H load. If the firing angle = 50, then the average output voltage is ______________________. Answer
Calculate the peak voltage across each half of a center-tapped transformer used in a full wave rectifier that has an average output voltage of 120 V. Consider ideal diode. Express your answer in four decimal places.
A three-phase bridge rectifier uses diodes rated at IdRMS = 145, VRRM =1000V and VD=0.7V. The rectifier isfed from a transformer with an inductance of 0,5mH per phase. Assume infinite inductive filtering and calculate, 1. the maximum DC output current;2. the maximum DC output voltage;3. the overlap angle.
A half wave rectifier feeds a load of 10ohms in series with inductance of 20mH. The input supply voltage is 200V and 50Hz, if the diode conducts 30 degrees during the negative half cycle. a) Calculate the average dc voltage at the load b) Calculate the time constant t c) Calculate the steady state current at t=11mSec
Single phase Full wave controlled rectifier with inductive load connected tо 120 V source. The R load equal 10 ohm, the inductive is very large. If the delay angle equal 30 degree Calculate 1- average load voltage 2-average load current 3-maximum load current 4-RMS load current 5-power supplied to the load 6-Form factor 7-ripple factor 8-draw the voltage source, V load, I load, current in each diode