A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox size. The input and output shafts should be in-line. Specify appropriate teeth numbers. The gearbox is required to transmit 18 kW from a shaft rotating at 2650 rpm. The desired output speed is exactly 13250 rpm. For space limitation and standardization reasons a double step-up gearbox is requested. Using the limited selection of gears presented in Tables 6.7 to 6.10, select suitable gears for the gears and pinions 2650 rpm 24 O 13250 rpm

A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox size. The input and output shafts should be in-line. Specify appropriate teeth numbers. The gearbox is required to transmit 18 kW from a shaft rotating at 2650 rpm. The desired output speed is exactly 13250 rpm. For space limitation and standardization reasons a double step-up gearbox is requested. Using the limited selection of gears presented in Tables 6.7 to 6.10, select suitable gears for the gears and pinions 2650 rpm 24 O 13250 rpm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotatingat 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40and 655M13, respectively State formula and standards relevant to the single step-up spur gearbox design
A compound gearbox is needed to provide 33:1 increase the speed, while minimizing the overall gearbox size. Specify appropriate teeth numbers.
For a pair of spur gears, one design decision is to specify the pressure angles. Please select the common values of pressure angle per textbook. 300 200 250
State the formula and standards relevant to the single step-up spur gearbox of 10kW rotating at 1000rpm with output speed of 1700rpm.Its materials are pinion with 20 teeth (655M13) and gear(817M40)
Select suitable gears for the gear wheels and pinion's for a gearbox required to transmit 17.75 kW from a shaft rotating at 2550rpm. The desired output speed is approximately 11925 rpm. For space limitation and standardization reasons, a double step-up gearbox is requested with equal ratios.Use the material '817M40'
Design A two stage spur gear reduction unit with 20- Deg full depth involute teeth. The input shaft rotates at 1440 rpm and receives 10 kW power. The speed of the output shaft should be approximately 180 rpm plus minus 5 rpm , All gears are made of steel and have the same module . Determine appropriate number of teeth of the gears in the unit .
Using this efficiency map, select a 6th gear ratio such that the engine will operate with high efficiency when travelling at 120km/h on a flat road. Give the total gear ratio and the ratio required in the gear box. State any assumptions and give engine speed and torque and approximate efficiency for your chosen gear ratio.
An epicyclic gear is designed as shown. The input A rotates at 100 rev/min clockwise viewed from the right with a torque of 20 Nm. The efficiency is 65 %. Calculate the following. The output speed and its direction The power output The holding torques Consider the operational efficiency for an epicyclic gearbox is 55%. Calculate the new output power of the gearbox and show how the efficiency value will affect the holding torque
A transmission system with a pair of beveled gears has the following data: 25° gear angle, 20° full depth involute system pressure angle, 5 in standard diametral pitch, both minion and gear are made of SAE 1040 steel and have a surface width of 3 in. If the number of pinion teeth is 20 and rotates at a speed of 2026 rpm so that the speed ratio becomes 1:5, then calculate how much HP power the system can safely transmit by a pair of inclined gears. To determine the maximum HP power that can be transmitted: (a) Using the modified Lewis and Buckingham equations, and(b) The AGMA method is based on strength only and uses the gear table to determine the required factors
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotating at 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40 and 655M13, respectively. Use table 6.10 on page 128 to select the suitable gear and pinion
Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the operating pressure angle is 20° The minimum value of addendum needed to ensure continuous transmission of motion is
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4