The diameters Dº & dº piped, Venturi-meter like horizontal water flow sistemseen in the drawing is connected to apiston - cylinder system of DPⓇ pistonand dp rod diameter and connectedto the incoming flow pipe and the cont-racted cross section.Assuming that the ideal - no head lossflow conditions are valid ;Calculate the force F applied to the pis-ton when the average velocity and thepressure at the entrance cross-sectionis V and p' respectively.Dº = 10 [mm]dº = 5 [mm]"&Ddpp*V-FD₂p = 4,5 [bar]Dp = 30 [mm]dºPwHorizontalSetupV = 5 [m/s]dp = 6 [mm]

Answered: Image /qna-images/answer/1c7c3929-c655-40aa-a9ce-024a9fbd0a35.jpg

The diameters D & d piped, Venturi- meter like horizontal water flow sistem seen in the drawing is connected to a piston - cylinder system of DPⓇ piston and dp rod diameter and connected to the incoming flow pipe and the cont- racted cross section. 6 Assuming that the ideal - no head loss flow conditions are valid; Calculate the force F applied to the pis- ton when the average velocity and the pressure at the entrance cross-section is V and p' respectively. Op* D dp # V p = 4,5 [bar] FD 1 dº P Horizon Setup V = 5 [m/s

The diameters D & d piped, Venturi- meter like horizontal water flow sistem seen in the drawing is connected to a piston - cylinder system of DPⓇ piston and dp rod diameter and connected to the incoming flow pipe and the cont- racted cross section. 6 Assuming that the ideal - no head loss flow conditions are valid; Calculate the force F applied to the pis- ton when the average velocity and the pressure at the entrance cross-section is V and p' respectively. Op* D dp # V p = 4,5 [bar] FD 1 dº P Horizon Setup V = 5 [m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.
The spiral conical draft tube are connected to Francis turbine. The diameters of the internal and external of tube are equal to 60 cm and 90 cm respectively. The tube should be drowned-approximately 1.5 meter below the lowest tail race level and draft tube high of 600 cm. The velocity at the exit is 1.5 meter per second. (Friction head loss in draft tube = 0.034 m ), calculate:- Find the pressure head at the entrance and the bottom in m of water and in Kg / cm?. the total heads at the same point with reference to the tail race as a datum find the power at the entrance and bottom the efficiency of a draft tube
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Water at 20°C is pumped through a smooth 12-cm-diameter pipe 10 kmlong, at a flow rate of 75 m3/h. The inlet is fed by a pump at an absolute pressure of 4 MPa.The exit is at standard atmospheric pressure (101 kPa) and is 200 m higher. Calculate the frictional head loss Hf and compare it to the velocity head of the flow.
The tank–pipe system of Fig. is to deliver at least11 m3/h of water at 20°C to the reservoir. What is themaximum roughness height ε allowable for the pipe?
A 230-m-long pipeline delivers 20◦C water to a storage reservoir located downstream. The pipeline is galva-nized with an average roughness height of 0.2 mm. An axial pump is used to pressurize upstream water. Thewater surface in the reservoir is located 18 m above the centerline of the pump. The pump discharges waterat an absolute pressure of 400 kPa and a volume flow rate of 50 L/s. Calculate a diameter of pipe requiredto achieve such an operating condition. If needed, use the Moody diagram on the last page, or one can solvethe Colebrook equation using, for example, Matlab.
For this siphon the elevations at A, B, C, and D are: 30 m, 32 m, 27 m, and 26 m, respectively. The head loss between the inlet and point B is three-quarters of the velocity head, and the head loss in the pipe itself between point B and the end of the pipe is one-quarter of the velocity head. For these conditions, what is the discharge and what is the pressure at point B? The pipe diameter 25 cm.
A 500 mm diameter pipe gradually reduces to 20 mm diameter and the gradually enlarge to its original size. Given the pressure at the base of the convergence of 0.60 MPa with a flow of 0.08 cu. m/s, 1. What is the velocity at point 1? 2. What is the velocity head at point 2? 3. Neglecting the head loss, the pressure of the smallest section is?
The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
Air flows through a Venturi channel of rectangular cross section as shown. The constant width of the channel is 0.06 m and the height at the exit is 0.04 m. Compressibility and viscous effects are negligible. (a) Determine the flowrate when water is drawn up 0.10 m in a small tubeattached to the static pressure tap at the throat where the channel height is 0.02 m. (b) Determine the channel height, h2, at section (2) where, for the same flowrate as in part (a), the water is drawn up 0.05 m. (c) Determine the pressure needed at section (1) to produce this flow.
estimate the allowable distance Y if the allowable pressure in the systems is -18kPa (gage). aasume that the volume flow rate is 5.6 x 10^-3 m^3/s
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3