A gearset consists of a 16-tooth pinion driving a 40-tooth gear. The diametral pitch is 2, and the addendum and dedendum are 1/P and 1.25/P, respectively. The gears are cut using a pressure angle of 20°. (a) Compute the circular pitch, the center distance, and the radii of the base circles. (b) In mounting these gears, the center distance was incorrectly made in larger. Compute the new values of the pressure angle and the pitch-circle diameters.

A gearset consists of a 16-tooth pinion driving a 40-tooth gear. The diametral pitch is 2, and the addendum and dedendum are 1/P and 1.25/P, respectively. The gears are cut using a pressure angle of 20°. (a) Compute the circular pitch, the center distance, and the radii of the base circles. (b) In mounting these gears, the center distance was incorrectly made in larger. Compute the new values of the pressure angle and the pitch-circle diameters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
Solve this problem in spur gearsA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressureangle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate theaddendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. Ifthe center distance isincreased by 0.125 in., what are the new valuesfor thecontact ratio and thepressureangle with complete solution and write in hand writing thank you
A pair of straight-tooth bevel gears (as shown in the figure above) are in mesh transmitting 35 hp at 1000 rpm (pinion speed). The gear rotates at 400 rpm. The gear system has a pitch of 6 and a 20-degree pressure angle. The face width is 2 inches and the pinion has 36 teeth. Determine the tangential, radial, and axial forces acting on the pinion
Two meshing spur gears with 20° pressure angle have a module of 4 mm. The centre distance is 220 mm andthe number ofteethonthe pinionis 40. What shouldbethe new centre distance so that pressure angle is increased to 22°?
A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
The lath machine in the university mechanical workshop uses epicyclic gear train shown in Figure 1 to operate. Plate gear Cof this gear system are carried on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as thesun wheel B for every five revolutions of the driving spindle carrying the sunwheel B.Determine suitable number of teeth for all the wheels and the exact diameter of pitch circle of the ring.1.1. Calculate the number of teeth of the ring gear D. 1.2. State an equation tha relate the number of teeth of gear D, B and C. 1.3. Use the table method to calculate the number of teeth of gear B. 1.4. Calculate the number of teeth for gear C.
Figure shows an alicyclic gear train with the following details:A has 40 teeth external (fixed gear) ; B has 80 teeth internal ; C - D is a compound wheel having 20 and 50 teeth (external) respectively, E-F is a compound wheel having 20 and 40 teeth (external) respectively, and G has 90 teeth (external). The arm runs at 100 r.p.m. in clockwise direction. Determine the speeds for gears C, E, and B.
A set of gears is used to reduce the speed from an electric motor to a shaft driving a grocery checkout conveyor, depicted below. The gear on the motor shaft is a 10-pitch pinion, has 18 teeth, and drives at 1200 rpm clockwise. The driven gear has 72 teeth. The motor has failed and is to be replaced with the only motor available, a 600 rpm motor with an 8-pitch pinion. Specify the set of commercially available 20⁰ spur gears, by number of teeth (N3and N4), that would result in the same conveyor speed and can be used without modification to the mounting (the center distance must not change). Find the number of teeth N3 on the pinion (drive) gear (teeth): Find the number of teeth N4 on the driven gear (teeth):
The figure shows a double-reduction helical gearset. Pinion 2 is the driver, and it receives a torque of 1200 Ibf • in from its shaft in the direction shown. Pinion 2 has a normal diametral pitch of 8 teeth/in, 14 teeth, and a normal pressure angle of 20° and is cut right-handed with a helix angle of 30°. The mating gear 3 on shaft b has 36 teeth. Gear 4, which is the driver for the second pair of gears in the train, has a normal diametral pitch of 3 teeth/in, 15 teeth, and a normal pressure angle of 20° and is cut left-handed with a helix angle of 15°. Mating gear S has 45 teeth. Find the magnitude and direction of the force exerted by the bearings C and D on shaft b if bearing C can take only a radial load while bearing D is mounted to take both radial and thrust loads.
The double-reduction helical gearset shown in the figure is driven through shaft a at a speed of 700 rev/min. Gears 2 and 3 have a normal diametral pitch of 12 teeth/in, a 30° helix angle, and a normal pressure angle of 20°. The second pair of gears in the train, gears 4 and 5, have a normal diametral pitch of 8 teeth/in, a 25° helix angle, and a normal pressure angle of 20°. The tooth numbers are: N, = 12, N, = 48, N4 = 16, N, = 36. Find: (a) The directions of the thrust force exerted by each gear upon its shaft (b) The speed and direction of shaft c (c) The center distance between shafts