A heat treat steel plate measures 3 m *1 m and is initially at 30 degree Celsius. It is cooled by blowing air parallel to 1 m edge at 9 km/hr. If the air is at 10 degree Celsius. Estimate the convective heat transfer from both sides of the plate

A heat treat steel plate measures 3 m *1 m and is initially at 30 degree Celsius. It is cooled by blowing air parallel to 1 m edge at 9 km/hr. If the air is at 10 degree Celsius. Estimate the convective heat transfer from both sides of the plate

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.7P

See similar textbooks

Related questions

Q: Consider two cases involving parallel flow of dry air at V = 3.5 m/s, T = 45°C, and atmospheric…

A: The thermal boundary layer is the flow zone over the surface where temperature change in the…

Q: Air at 1 atm and 27 C enters a rectangular duct that is 1 m long with a cross-sectional area that…

Q: Use the thermal wind equation to explain the presence of the jet stream.

A: The Thermal Wind expression can be derived from the geopotential Equation as: Thermal wind is a…

Q: Air stream (k = 0.02439 W/m.K, v = 1.426 x10 ' m2/s, Pr = 0.7336) flows over a flat surface [L= 4.5…

Q: 4.17 Consider a flat plate with a chord length (from leading to trailing edge) The free-stream flow…

Q: The velocity and temperature behind a normal shock wave are 329 m/s and 1500 K, respectively.…

A: Step-1 The velocity of the normal shock wave is: v2 = 329 m/s The temperature of the normal shock…

Q: A constant-area duct that is 20 cm in length by 2 cm in diameter is connected to a reservoir through…

A: Now the mass flow rate is givenm˙=ρAV2Now we have bernoullis equation ash1+V122=h2+V222We…

Q: Consider two cases involving parallel flow of dry air at V = 3.5 m/s, T = 45°C, and atmospheric…

Q: Air enters a rectangular duct measuring 30 cm by 40 cm with a velocity of 8.5 m/s and a temperature…

Q: Imagine a plate 1 m long by 1 m wide at a temperature of 80 °C. Water is passed over its surface at…

A: Length of the plate, L=1 mWidth of the plate, W=1 mTemperature of the plate, Ts=80oCSpeed of water,…

Q: . Oil enters a 1.25-cm diameter,3-m long tube at 38°C. The tube wall is maintained at 66°C, and flow…

Q: Consider two cases involving parallel flow of dry air at V = 5 m/s, T=45°C, and atmospheric pressure…

Q: Consider Couette flow for two plates separated by a 6 inch-thick layer of 10W-30 oil. The top plate…

Q: ir is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8…

Q: Consider a normal shock wave in air where the upstream flow properties are u1 = 690 m/s, T1 = 288 K,…

Q: Consider a normal shockwave in air where the upstream flowproperties are u1 = 680 m/s, T1 = 288 K,…

A: Given data: The upstream velocity is, U1 = 680 m/s. The upstream temperature is, T1 = 288 K. The…

Q: Example 4: Hot air at atmospheric pressure and 80°C enters an 8–m-long uninsulated square duct of…

Q: Water at 30 °C enters a pipe of 25 mm in diameter and 1 m in length with a mean velocity of 0.06…

Q: A parallel flow between two large isothermal plates with one plate moving at a constant velocity of…

Q: Consider a flat plate with a chord length (from leading to trailing edge) of 1 m. The free-strean…

Q: Consider two cases involving the parallel flow of dry air at V= 1.5 m/s, T∞=45°C, and atmospheric…

A: To find: The location where the thermal boundary layer thicknesses of the two cases equal, and also…

Q: An industrial gas at a pressure of 3.5 atm and 27°C blows over a 50-cm x 50-cm plate at an average…

A: Given Data The pressure of the gas, P=3.5 atm The temperature of the gas, T=27°C Constant wall…

Q: Saturated water at 50° C flows over a 150 cm long flat plate with a velocity of 3 m/s. The plate…

Q: cylindrical electrical heating element (dissipated 1000 W/m) of diameter D=10 mm, thermal…

Q: Consider two cases involving parallel flow of dry air at V = 4.5 m/s, T = 45°C, and atmospheric…

Q: A tube bank uses a staggered arrangement of D=0.9 cm diameter tubes with S7=2 cm and SL=1.7 cm.…

Q: Atmospheric air at 25oC and with a speed of 50 m/s is pumped by a fan over a flat plate. a)What is…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Example 2: The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air…

Q: (b) Air at 25 °C flows past a flat plate at 1.5 m/s. The plate measures 500 mm (length) x 200 mm…

A: b) Pr=0.796V=1.5 m/sν=1897×10-6 m/s2K=0.03896 wmKnow calculate Reynold…

Q: Consider two cases involving parallel flow of dry air at V=V= 2.5 m/s, T∞=45°C, and atmospheric…

Q: A tube bank uses a staggered arrangement of D=0.9 cm diameter tubes with S,=2 cm and S=1.5 cm. There…

Q: 3.0 Consider two cases involving parallel flow of dry air at V=V= 1.5 m/s, T∞=T∞=45°C, and…

Q: Air at 200C and at a pressure of 1 bar is flowing over a flat plate at a velocity of 3 m/s. If the…

A: Given: Pressure P=1 bar, velocityV=3 m/s, palate is w=0.280 m wide , temperatures are T1=200°C and…

Q: In the effort to increase the removal of heat from a hot surface at 120°C, a cylindrical pin fin (kf…

A: The properties of air at a temperature of 70 oC are given as, The characteristic length of the…

Q: Water (7.7 L/min) is flowing in a tube "D = 3 cm, L= 5 m" and is to be heated from 15°C to 62.1°C by…

A: Given:Volume flow rate,Q=7.7Lmin=7.7×10-360m3sDiameter of tube,D=3cm=0.03mLength,L=5mInitial…

Q: Air flows over a flat plate with a velocity u = 13 m/s and temperature Te = 25 °C. The plate surface…

A: Use Reynold number and nusselt number expression to differentiate the flow region.

Q: Air at atmospheric pressure and temperature of 25 oC flows at a speed of 10 m/s along a flat plate…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Oil enters a 1.25-cm diameter,3-m long tube at 38°C. The tube wall is maintained at 66°C, and flow…

Q: Air that is fully-developed flows in a rectangular duct of inside dimensions 0.610 m x 0.305 m. The…

A: given, we have h=0.610m b=0.303 m L=2.44 m τmi=21.1°CTm.0 =26.7°Cm=2.72 kg/n

Q: A plate with negligible thickness of 50 cm and a length of 100 cm is exposed to 2 different air…

A: Given dataWidth of the plate t = 50cm = 0.5mLength of the plate L = 100cm = 1mSpeed of air flowing…

Q: Air at atmospheric conditions (101.3 kPa and 20° C) enters the bottom of a 90° conical flowmeter…

A: Given, Mass flow rate, m=0.4kg/sPressure, P=101.3KPaTemperature, T=20°C=293KDiameter , d=7.5cmFrom…

Q: Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge.…

A: Air Temperature, T∞=20oC Air Velocity, U∞=4.5m/s Plate Temperature, Ts=60oC

Q: 6- Air at a pressure of 200 kPa and free-stream temperature of 27 C flows over a square flat plate…

Q: A long pipe

A: Note: As per Bartleby guidelines only 3 subparts have to be solved at a time. So upload other parts…

Q: For a fixed compressor inlet velocity and flow area, explain the effect of increasing compressor…

A: Given Data⇒fixed compressor inlet velocityflow areaProblem statement⇒Problem says determine the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider two cases involving parallel flow of dry air at V=V= 2.5 m/s, T∞=45°C, and atmospheric pressure over an isothermal plate at Ts=20°C. In the first case, Rex,c=R⁢ex,c=5 × 105, while in the second case the flow is tripped to a turbulent state at x=0 m. a. At what x‐location, in m, are the thermal boundary layer thicknesses of the two cases equal? in m b. what is the q'' lam at W / m^2 c. what is the q'' turb at W / m^2
Ethylene glycol at 40°C flows over a heated plate very wide, 6 m long, at velocity of 0.04 m/s. For a temperature = 90°C, determine: 1- the thickness of the hydrodynamic boundary layer at the end of the plate2- the thickness of the thermal boundary layer at the end of the plate3- the local and average heat transfer coefficient at the end of the plate4- the total heat flux transferred from the heated surface.
8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of the stack necessary for a driving pressure of 0.20 KPaKindly answer all please. Thank you
Air is flowing at a speed of 30 m/sec over a flat plate. The air temperature is 20o C and its pressure is 1 atm. The plate is kept at a constant temperature of 65o C. What is the heat transfer rate per unit length between 7.5 cm to 30 cm, from the edge of the plate?
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C . The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 °C , what is the overall heat transfer at the laminar section?
Assuming that the velocity profile in a laminar boundary layer of thickness δ is given by where u is the velocity at distance y from the surface and Ue is the freestream velocity (as shown in Figure P9.23), demonstrate that where θ is the momentum thickness, τw is the viscous stress at the wall, Cf is the local skin friction coefficient at a distance x from the leading edge of the plate, ρ is the density and ν is the kinematic viscosity.
Example 2: The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure is 20°C flows with a velocity of 8 m/s over a 1.5 m  6 m flat plate whose temperature is 140°C (Figure). Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side and (b) the 1.5-m side.
Sketch the velocity gradients that arise from pressure-driven flow for a Newtonian liquid and a shear thinning liquid.
Air is flowing at a speed of 5 m/sec between two parallel flat plates. The air temperature is 20o C and its pressure is 1 atm. The plates are kept at a constant temperature of 90o C and the distance between them is 60 cm. The plates width is 1 m and their length is 1.5 m. What is the electrical power required to keep the plates at constant temperature?
Answer completely. The Fanning equation is essentially the same as the Darcy-Weisbach equation but differs by their friction factors. What is the relationship between the friction factor, f, of the Darcy-Weisbach equation and the friction factor, f’, of the Fanning equation?
Atmospheric air at 5°C enters a thin walled 12cm diameter 20m long isothermal pipe (Ts=constant) at a velocity of 2.5m/s and leaves at 19°C. Estimate the surface temperature Ts.
Prove that the thermocouple will underestimate the temperature of airflow by more than 15% but less than 30% in a large air duct if the temperature of the hot air is 1367 K, duct-wall temperature is 533 K, emissivity of the thermocouple is 0.5, and the convection heat-transfer coefficient is 114 W/m2 -K.