(b) Air at 25 °C flows past a flat plate at 1.5 m/s. The plate measures 500 mm (length) x 200 mm (breadth) and is maintained at a uniform temperature at 85 °C. Calculate the heat loss from the plate, if the air flows parallel to the plate. Pr = 0.796 y = 1897 x 10 m²/s k = 0.03896 W/m K 0.5 = 0.332Re, pr0.333 Nu L

(b) Air at 25 °C flows past a flat plate at 1.5 m/s. The plate measures 500 mm (length) x 200 mm (breadth) and is maintained at a uniform temperature at 85 °C. Calculate the heat loss from the plate, if the air flows parallel to the plate. Pr = 0.796 y = 1897 x 10 m²/s k = 0.03896 W/m K 0.5 = 0.332Re, pr0.333 Nu L

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.30P: Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart....

See similar textbooks

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
Laminar flow occurs when the Reynolds number (Re*) is below 2000; turbulent flow occurs when the Reynolds number is above 2000. For the following species, determine the maximum value of the average 1D speed for which laminar flow will occur: a) Ne at 293 K where ?η is 313 ?μP and ?ρ = (PM)/(RT) through a 2.00 mm (id) pipe b) Liquid water at 293 K where ?η is 0.891 cP and ?ρ = 0.998 g/mL through a 2.00 mm (id) pipe *Re = (?ρ **d)/?η, where d is the diameter of the tube through which the fluid is flowing.
Consider turbulent fl ow past a sharp, smooth fl at plate ofwidth b and length L. What percentage of the friction dragon the plate is carried by the rear half of the plate?
Air flows at Q=5 m³/s in a 1-m diameter stainless steel duct (roughness of 0.002 mm) the air properties are (-1.23 kg/m³ and -1.8 x 10^5N-s/m²). Approximate the minimum length of the duct so that entrance lengths can be ignored in the calculation of the pressure drop. a.41.1 m b.206 m c.20.6 m d.0411 Option a is incorrect
Air at uniform U velocity flows over flat square shaped plates with different arrangements given in the figure below. (a) uses one plate, (b) uses four square plates. All plates are the same size. What is the friction forces ratio (Fb/Fa)? (NOTE: Assume laminar nerve layer condition throughout plate arrangements)
Explain briefly in your own words (parts a-d)a) Why doesn’t the surface roughness affect the pressure drop in a laminar pipe flow? b) For bluff bodies, the drag coefficient decreases abruptly when the flow becomes turbulent. Why? c) Consider a spinning ball (in the clockwise direction) moving with a velocity U. Explain how the lift force is formed on the ball and show its direction. Uwd) For flow over streamlined bodies, drag force usually increases when the flow becomes turbulent.Why? e) Consider a pipe with a radius R and length L (extending from (1) to (2)). Inside the pipe there is a solid cylinder with a radius k×R (k  1). The planes (1) and (2), separated by a distance L have pressures P1 and P2 respectively, with P1 > P2. At t = 0, the inner solid cylinder suddenly begins to be pulled at a constant speed U in the negative z direction. Thefluid is an incompressible Newtonian liquid with dynamic viscosity μ and density ρ. In orderto find the solution for the velocity field in…
Answer completely Show how the Darcy-Weisbach equation can be derived from the Hagen-Poiseuille equation through the introduction of the Reynolds number. What is the friction factor, f, equal to for flow at a laminar condition? What is it equal to in other regimes of flow?
Engine oil at 100°C flows on the top surface of a 1-m-long flat plate maintained at 20°C. The oil’s freestream speed (u infinity) is 0.1 m/s. Find the engine oil properties from the table A.5 A. Evaluate the Reynolds number, local convection coefficient, heat flux and shear stress at the end of the plate (x = L). Is the air flow laminar or turbulent over the plate?B. Evaluate the average convection coefficient, average heat flux, average shear stress and drag force over the plate.
Air at 20°C flows at V = 80.0 m/s over a smooth flat plate of length L = 17.5 m. Plot the turbulent boundary layer profile in physical variables (u as a function of y) at x = L. Compare the profile generated by the one-seventh-power law, the log law, and Spalding’s law of the wall, assuming that the boundary layer is fully turbulent from the beginning of the plate.
The exact expression for the local Nusselt number for laminar flow along a flat plate is given by: Nux=h(x)x/k=0.332Pr1/3Rex1/2. Atmospheric air at Tinf=400K with a velocity uinf=1.5m/s flows over a flat plate L=2m long maintained at a uniform temperature Tw=300K. Calculate the heat transfer rate from the airstream to the plate from x=0 to x=L=2m for w=0.5m. A. 234 W B. 334 W C. 434 W D. 134 W
An air compressor increases the pressure (Pout > Pin) and the density (?out > ?in) of the air passing through it. For the case in which the outlet and inlet diameters are equal (Dout = Din), how does average air speed change across the compressor? In particular, is Vout less than, equal to, or greater than Vin? Explain.
Consider the laminar boundary layer flow of an isothermal fluid ( U ∞ , T ∞ ) over a flat isothermal wall ( T 0 ). At a certain distance x from the leading edge, the local skin friction coefficient is C f , x = 0.0066. What is the value of the local Nusselt number at the same location if the Prandtl number is Pr = 7?