Water at 30 °C enters a pipe of 25 mm in diameter and 1 m in length with a mean velocity of 0.06 m/s. The pipe surface temperature is 50 °C. What is the outlet temperature of water? Assume the fully developed condition. For water: k = 0.6 W/mK, ν = 0.8x10-6 m2/s, ρ = 1000 kg/m3, cp = 4187 J/kgK, Pr = 5

Water at 30 °C enters a pipe of 25 mm in diameter and 1 m in length with a mean velocity of 0.06 m/s. The pipe surface temperature is 50 °C. What is the outlet temperature of water? Assume the fully developed condition. For water: k = 0.6 W/mK, ν = 0.8x10-6 m2/s, ρ = 1000 kg/m3, cp = 4187 J/kgK, Pr = 5

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

Answer completely Show how the Darcy-Weisbach equation can be derived from the Hagen-Poiseuille equation through the introduction of the Reynolds number. What is the friction factor, f, equal to for flow at a laminar condition? What is it equal to in other regimes of flow?
Laminar flow occurs when the Reynolds number (Re*) is below 2000; turbulent flow occurs when the Reynolds number is above 2000. For the following species, determine the maximum value of the average 1D speed for which laminar flow will occur: a) Ne at 293 K where ?η is 313 ?μP and ?ρ = (PM)/(RT) through a 2.00 mm (id) pipe b) Liquid water at 293 K where ?η is 0.891 cP and ?ρ = 0.998 g/mL through a 2.00 mm (id) pipe *Re = (?ρ **d)/?η, where d is the diameter of the tube through which the fluid is flowing.
Pressure Drop of Power-Law Fluid in Laminar FlowA power-law fluid having a density of 1041 kg/m3 is flowing through 14.9 m of a tubing with an inside diameter of 0.0524 m at an average velocity of 0.0728 m/s. The rheological or flow properties of the fluid are K′ = 15.23N·sn′/m2 (0.318 lbf·sn′/ft2) and n′ = 0.40. Calculate the pressure drop and friction loss using Eq. (9.1-10) for laminar flow. Check the generalized Reynolds number to make sure that the flow is laminar. Repeat part (a) but use the friction-factor method
Turbulent Flow of a Power-Law Fluid A pseudoplastic fluid that follows the power law, having a density of 961 kg/m3, is flowing through a smooth, circular tube having an inside diameter of 0.0508 m at an average velocity of 6.10 m/s. The flow properties of the fluid are n′ = 0.30 and K′ = 2.744 N·sn/m2. Calculate the frictional pressure drop for a tubing 30.5 m long.
Air at atmospheric pressure and temperature of 25 oC flows at a speed of 10 m/s along a flat plate that is 4 m long and has a uniform surface temperature of 140 oC. Ifcritical Reynolds number of 200,000:a) the local heat transfer kingdom at x = 2; 3; and 4 m from the front rim.b) the average heat transfer balance is 4 m long.c) the rate of heat transfer from the surface of the plate to the air if the width of the plate surface is 2 m.d) game problems b) and c) flow velocity 5 and 20 m/se) What is your analysis and conclusion on this case?
Assuming an air density of 1.22kg/m3, calculate (1) the pressure loss for a ventilation airway transition from a 1m diameter duct to a 1.2m diameter duct at a flow rate of 19 cubic metres per second with an abrupt expansion transition shock factor of 0.24; (il) the dynamic or velocity pressure in both ducts.
Consider two cases involving parallel flow of dry air at V=V= 2.5 m/s, T∞=45°C, and atmospheric pressure over an isothermal plate at Ts=20°C. In the first case, Rex,c=R⁢ex,c=5 × 105, while in the second case the flow is tripped to a turbulent state at x=0 m. a. At what x‐location, in m, are the thermal boundary layer thicknesses of the two cases equal? in m b. what is the q'' lam at W / m^2 c. what is the q'' turb at W / m^2
The exact expression for the local Nusselt number for laminar flow along a flat plate is given by: Nux=h(x)x/k=0.332Pr1/3Rex1/2. Atmospheric air at Tinf=400K with a velocity uinf=1.5m/s flows over a flat plate L=2m long maintained at a uniform temperature Tw=300K. Calculate the heat transfer rate from the airstream to the plate from x=0 to x=L=2m for w=0.5m. A. 234 W B. 334 W C. 434 W D. 134 W
Consider a flow of SAE 30W oil at 20°C through a 2.4-cm-diameter smooth pipe at 1 million N/h. Determine the Reynolds number for this flow. For SAE 30W oil at 20°C, take ρ = 891 kg/m3, μ = 0.29 kg/m-s, and π = 22/7. The Reynolds number is
Air flows at Q=5 m³/s in a 1-m diameter stainless steel duct (roughness of 0.002 mm) the air properties are (-1.23 kg/m³ and -1.8 x 10^5N-s/m²). Approximate the minimum length of the duct so that entrance lengths can be ignored in the calculation of the pressure drop. a.41.1 m b.206 m c.20.6 m d.0411 Option a is incorrect
Air at 1.7 atm gauge and 15°C enters a horizontal 75-mm steel pipe that is 70 m long. The velocity at the entrance of the pipe is 60 m/s. Assuming isothermal flow, what is the pressure at the discharge end of the line? ANSWER SHOULD BE 1.982 atm
For what value of Reynolds number flow is laminar in flat plates?