A heated flat plate is exposed to the colder air flowing over the plate at a velocity of 35 ft/s. The plate is at a temperature of 200 F while air is at atmospheric pressure and 70 F. Find the rate of heat transfer if the plate is a) heated at the leading edge and b) at a distance of 3 in from the leading edge

A heated flat plate is exposed to the colder air flowing over the plate at a velocity of 35 ft/s. The plate is at a temperature of 200 F while air is at atmospheric pressure and 70 F. Find the rate of heat transfer if the plate is a) heated at the leading edge and b) at a distance of 3 in from the leading edge

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.32P

See similar textbooks

Similar questions

Air at a temperature of 95 F and a velocity of 20 ft/s flows over a hot flat plate, maintained at 482 F. Find the rate of heat transfer form this 1ft by 1 ft square plate. And find the distance from the surface of the plate where flow velocity becomes 75% of the free stream velocity at x = L/2.
A bathroom extractor fan being sold on Amazon has a duct diameter of 10.0 cm. It extracts air from a bathroom at a rate of 70.0 m3/h and the power supplied to the fan is 7.0 W. With what efficiency does the extractor convert electrical power into the kinetic power associated with the air-motion? Take the density of air to be 1.2 kg/m3 and assume laminar air flow.
An airplane with a 1.8m diameter propeller travels in still air with a density of 1.14 kg/m3 at 85m/s. is doing. The speed of the air passing through the propeller is 115 m/s relative to the plane. a) the thrust on the aircraft, b) theoretical horsepower required to turn the propeller, c) propeller efficiency, and d) across the blade Determine the pressure difference.
‏During a flow process 5000 W paddle wheel work is supplied while the internal energy of the system increase in one minute is 200 kJ . The heat transfer is
A site is being considered for wind power generation. At this site, the wind blows steadily at 6 m/s for 3,323 hours per year. Assuming the wind velocity is negligible at other times for simplicity, determine the kWh/year that can be produced at the site for a turbine with a mechanical efficiency of 100% and an effective flow area of 5 m2. Use a value of 1.25 kg/m3 for the density of the air. Give your answer in killowatt-hours per year (kWh/year). Hint: I reccomend starting by finding the kinetic energy (kJ/kg) of the wind. Hint 2: Multiply the power generation (kW) by the number of hours of wind per year (h/year) to get kWh/year.
Q6) (a) Two sites are being considered for wind power generation. In the first site, the wind blows steadily at 7 m/s for 3000 hours per year, whereas in the second site the wind blows at 10 m/s for 2000 hours per year. Assuming the wind velocity is negligible at other times for simplicity; determine which a better site is for wind power generation. Hint: Note that the mass flow rate of air is proportional to wind velocity. (Take the density of air to be ? = 1.25 kg/m3).
Air at a temperature of 95 F and a velocity of 20 ft/s flows over a hot flat plate, maintained at 482 F. Find the rate of heat transfer form this 1ft by 1 ft square plate. [Ans. ~ 423 Btu/hr].
The actual velocity of a gas entering in a chimney is 8 m/sec the gas temperature is 25 C and pressure of 98 Kpa with a gas of 0.287 KJ.kg-K . Determine the chimney diameter in meter if mass of gas is 50000 kg/hr.
A wind generator that is 50 m in diameter is subjected to winds of 20 m/s. If the turbine has an efficiency of 40%, what is the power generated? and what is the force exerted by the wind?
One kg water at velocity 12.5 m/s and 30oC enters a 2.54 cm diameter horizontal pipe where there is no heat or work exchange with the surroundings. The water suddenly flows through a larger pipe with a diameter of 3.85cm. Calculate the following:a. Velocity of the water leaving the pipe in m/sb. The change in temperature of the water. Cpwater=4.18 ????.?
Pinch temperature at hot stream is 70C, while at cold stream is 60C
Solve for the latent heat of water at Tw = 28C(and. λw = 2435 kJ/kg)