A high-alloy steel with 0.15% C, 10% Cr, 8% Ni, 2% Mo and a small amount of V in its composition. Write the short designation according to DIN standards.

Q: In general Poisson’s ratio of steel is ________ Select one: a. 0.5 b. 0.15 c. 0.3 d. 0.75

A: When a force is employed to a specimen along its longitudinal direction, the stain will be induced…

Q: What are heat-treatable and non-heat-treatable aluminum alloys?

A: Heat treatable aluminum alloys: They consist of pure aluminum that is heated to a critical…

Q: Write a short representation of a high alloy steel with 0.15% C, 10% Cr, 8% Ni, 2% Mo and a small…

A: The short representation will start with a set of digits representing 100 times the percentage of…

Q: Explain why a 92% copper – 8% nickel can or cannot be age hardened.

A: Age hardening: Age hardening is a heat treatment process that is used to increase the yield strength…

Q: ghtly below 723°C. Calculate the weight percent proeutectoid ferrite in the steel. Calculate the…

A:

Q: Using the lever rule, calculate the amount of ferrite in a 0.42% C steel at 727 degrees celcius.

A: given data- amount of carbon = 0.42 % at 727 deg C to determine-  amount of ferrite

Q: In the AISI steel alloy group numbering system, alloys ASI 40 XX through the ASI 48XX are vanadium…

A: Given codes: ASI 40 XX ASI 48XX Need to decide whether the given statement is True or False.

Q: f) For the Ag-20% Cu and Ag-80% Cu alloy; from 1100°C to room temperature,

A:

Q: AISI 5XXX, 51XX, 51100, and 52100 chromium alloy steels are considered as stainless steel's since…

A: AISI 5XXX, 51XX, 51100, and 52100 chromium alloy steels are considered as stainless steel's since…

Q: The Melting temperature of Alloys occurs in a range of temperature?

A: given; -The Melting temperature of Alloys occurs in a range of temperature?

Q: What is the tensile strength of the aluminium and iron alloys

A: Aluminium is an element having major constituent of Al. In periodic table it belongs to 13th group.…

Q: Write a short representation of 0.15% C, 10% Cr, 8% Ni, 2% Mo and a small amount of Flywheel high…

A: composition will be like0.15%C , 10%Cr , 8%Ni ,2%Mo

Q: a) Pure metals usually do not possess the right properties for most structural applications;…

A:

Q: 18. What is the range of carbon concentrations for steels? 4.3...6.67% 0.8...6.67% 0.8...2.14%…

A: For low carbon steel , 0.05 to 0.26% For medium carbon steel, 0.29 to 0.54% For High carbon steel,…

Q: What are the properties of Alloy Steel and brief descriptions of it?

A: an alloy steel  may be defined as carbon steel to  which one or more elements are added so that it…

Q: a combination of elements which possesses metallic properties is called an alloy. discuss how…

A:

Q: 1.a) Write a short representation of 0.15% c, 10% Cr, 8% Ni, 2% Mo and a small amount of Flywheel…

A: As per Turkey standard of designating a alloying element The first set of digits represents the…

Q: Compute the fraction of Al2Cu intermetallic at a temp of 500 degrees C for an alloy of 10% copper in…

A: Apply the tie rule to determine the Al2Cu in 10% cu concentration. Consider the diagram as shown.

Q: 2-15 What are the principal alloy elements of an AISI 4340 steel? How much carbon does it have? Is…

A: Different types of steels used in engineering applications are: Low carbon steel Medium carbon…

Q: Rank the following four iron-carbon alloys from the hardest to the softest. Fe;C- Fe;C- Fe,C- Fe,C…

A: Given : The different iron carbon alloys.

Q: Write down the percentage of% C and other alloying elements of the steel given the short designation…

A: the percentage of% C and other alloying elements of the steel given the short designation 10CrMo910

Q: 1. (a) Calculate the amounts of ferrite, cementite, primary microconstituent, and pearlite in the…

A: Given data: Steels101510351095 Need to determine the amounts of ferrite, cementite, primary…

Q: The Molybdenum content in Molybdenum - Steel (4430) according to SAE/AISI classification system is O…

A: The Molybdenum content in Molybdenum - Steel (4430) according to SAE/AISI classification system is..…

Q: Alloying element and structure of Stainless steel

A: Solution:

Q: Normalizing is softening process in which iron base alloys are heated ____ above the upper critical…

A: Given :-  Normalizing is softening process in which iron base alloys are heated ____ above the upper…

Q: Determine the temperature that should be used to normalize (a) a 1030 steel, (b) a 1075 steel and…

A: Normalizing is a process of heating a material to elevated temperature and then cooling of the…

Q: Write a short representation of an automaton steel with 0.20% C, 0.28% S, 1.1% Mn and 0.2% Pb in its…

A: The first set of digits in the short representation of the alloy will contain hundred times the…

Q: Specify the number of degree of freedom for the following alloys. Refer to the pictures below. A) 95…

A: The expression for the Gibbs phase rule in the general form is given as, P+F=C+N......(1) Here, P is…

Q: (b) Figure 1 shows, the tensile engineering stress-strain curve for an aluminum alloy. Based on…

A: According to the details provided in the question, we need to calculate  1. yield strength  2.…

Q: What is the composition (wt% C) of a steel with AISI designation 1090? . Would this be considered a…

A: Iron is a common name for a large family of steel alloys. Metals can be cast directly into the mold,…

Q: What are called copper alloy? Name any three copper alloys with its alloy metals,, specify its…

A: Let us discuss about copper alloys in detail.

Q: What is high copper content alloys and what is its significance?

A: The (copper) alloys with carbon percentage 96 to 99% termed as High copper alloys

Q: Determine the specific strength of the strongest Al, Mg, Cu, Ti, and Ni alloys.Use the densities of…

A: Specific strength of any material states that the ratio of yield strength of material to the density…

Q: r and copper alloys as specified by the copper development association CDA and are designated as…

A: No, It is false.

Q: Q2 (1p) Schematic room temperature microstructuresfor four iron-carbon alloys are shown below. 1-…

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

Q: What are the applications of Aluminum and Zinc Alloys? (b) : Explain the Rolling process of metals…

A:

Q: what selection criteria could be used to determine the fatigne strength of terrons and Non-ferrons…

A: Materials have been known to fail in service when subjected to recurrent loads well below their…

Q: Specify a copper alloy that requires at least 50% elongation and at least 300 MPa tensile strength.

A: The stress-strain curve for a copper alloy (Brass) is given as under:

Q: Write the % C and other alloying elements percentages of the steel whose shorthand notation as…

A:

Q: The addition of alloying elements to high carbon steel alloys increase their wear resistance, due to

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: what is fracture stress,ductility and modulus of resilience for 304 Stainless Steel and 6061-T6…

A: Fracture stress is also known as the breaking strength of the material at which the material fails…

Q: Calculate the ductility of this steel alloy in %EL.

A:

Q: for four different metals: 2014-T6 aluminum, 6061-T6 aluminum, structural A-36 steel, and 304…

A: Structural steel is one of the most often utilized materials in commercial and industrial…

Q: Select from list A the most suitable metal or alloy for the application in list B ? List A Plain…

A: In material science, Each material has its own quality and properties. According to requirements,…

Q: Explain and justify use of Titanium and its alloys in following application: • Bicycle frame •…

A: Use of titanium in bicycle frame The tensile strength of the titanium is very high as compared to…

The Space Lattice and Unit Cells

Every matter consists of atoms, molecules, and ions. If these atoms, molecules, and ions (micro-particles) are represented in a three-dimensional space-occupying certain specific points in space, then these arrangements are termed as space lattices and the specific points which are being occupied by atoms, molecules and ions are termed as lattice points. The atoms, molecules, and ions at the lattice points are generally grouped in a regular fashion and repeat periodically at the three-dimensional space.