1.a) Write a short representation of 0.15% c, 10% Cr, 8% Ni, 2% Mo and a small amount of Flywheel high alloy steel according to Turkish standards in its compositic b) Write a short representation of an automaton steel with 0.20% c, 0.28% s, 1.1% Mn and 0.2% Pb in its composition according to Turkish Standards. c) Write the% c and the percentages of other alloying elements of the steel, which is given a short designation as 10CPM0910. d) Write down the% C and the percentages of other alloying elements of the steel given a short designation as 45CrVMoW58. e) what is the% C ratio of two different steels with 80% and equal austenite content at 724 C?

1.a) Write a short representation of 0.15% c, 10% Cr, 8% Ni, 2% Mo and a small amount of Flywheel high alloy steel according to Turkish standards in its compositic b) Write a short representation of an automaton steel with 0.20% c, 0.28% s, 1.1% Mn and 0.2% Pb in its composition according to Turkish Standards. c) Write the% c and the percentages of other alloying elements of the steel, which is given a short designation as 10CPM0910. d) Write down the% C and the percentages of other alloying elements of the steel given a short designation as 45CrVMoW58. e) what is the% C ratio of two different steels with 80% and equal austenite content at 724 C?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 - Which is not a shaping process? A) particle processing techniques B) plastic forming C) chip removal D) solidification techniques E) electrolysis 2 - What to expect from a superconducting material? A) direct conductivity B) insulation C) semiconductivity D) metastable state E) zero resistivity 3 - What is the other name of austenitic stainless steels? A) P91 steels B) 18-8 steels C) P92 steels D) O1 steels E) H11 steels 4 - Which is not a physical property of matter? A) volumetric B) electrical C) thermal D) mechanical E) electrochemical 5 - Which one has…
1. Distinguish dispersion hardening and precipitation hardening. 2. A design has the following functional requirements: a) High dimensional stability at high temperature. b) Must not buckle under its own weight.Suggest a material attribute to fulfil each functional requirement. Support your answers.
1- what materials are included here (z parameter), type of materials considered, property or properties plotted, domain of c, parameter identified 2- what are the vertical and horizontal trends presented 3-what is the take away story from this plot please answer i will upvote
When designing a matrix acidizing treatment, the following parameter does not need to be considered: a. Formation mineralogy b. Reservoir thickness c. Formation closure stress d. Extent of damage
How would you callout magnesium in an engineering drawing note? I want to call out Magnesium AZ31B, plate, AMS4376. This is what I have so far: Notes: 1. Material: MAGNESIUM ALLOY, PLATE, UNS M11311 (AZ31B), PER AMS4376, CONDITION -H26 Is this correct?
What is the difference between normalizing process, annealing process, hardening process and tempering process? With net sketch
Percentage elongation and percentage contraction of area are measures of a materials'
Given the following data for five different materials answer parts A B C D E & F with an explanation
In your summer internship, you are tasked with measuring the ultimate tensile strength of a material to determine if it meets your company’s (Superior Super Ships Inc) specification. Your boss is worried that the new low-cost supplier, Shoddy Alloys Inc, may not be reliable but it is the only way to source on-time the SS304 needed to make finishings for Jeff Bezos’ new yacht, the Black Pearl. You collect several load versus displacement curves, as illustrated below. The initial diameter of the round gauge section is 0.25 in. You also collect the instantaneous diameter of the specimen during the test using a laser. Using the provided data, calculate what is the ultimate tensile strength measured in this test?
In the iron carbon phases diagram, Greek letters and names of structures are used L liquid metal FE 3C iron carbide Delta Delta iron gamma gamma iron called austenite alpha alpha iron called ferrite true or false?
An engineer is making determinations on the best alloy of steel to use in cables for a cable-stayed bridge. The investigator’s tool is a tensile testing instrument which can measure the strength of the alloys by slowly increasing the load on the cable to the point where the cable breaks and breaking point value (amount of weight on the cable when it fails) can be accurately measured. The investigator also is interested in determining the amount of deformation of the cable (how much it stretches under load conditions which is also very important in structural considerations. The tests must be uniform and consistent to give the precision needed to make valid conclusions about the best alloy for the cables. On the line after the item, identify which type of variable it represents from (a) independent variable, (b) dependent variable, (c) control variable. 1) thickness of the cable _____________ 5) length of the cable _____________ 2) testing room temperature…
During 650°C, the average grain diameter of a brass material was measured as a function of time, as seen below at two distinct points of Time (min) Grain Diameter (mm) 30 3.9 × 10^-2 90 6.6 × 10^-2 a. What was the grain diameter at the start? (orig diameter) b. What is the expected grain diameter after 150 minutes at 650 °C?