A hollow cylindrical rod (rod 1) and a solidcylindrical rod (rod 2) are made of the same material. The tworods have the same length and the same outer radius. If the samecompressional force is applied to each rod, (a) is the change inlength of rod 1 greater than, less than, or equal to the change inlength of rod 2?

A hollow cylindrical rod (rod 1) and a solidcylindrical rod (rod 2) are made of the same material. The tworods have the same length and the same outer radius. If the samecompressional force is applied to each rod, (a) is the change inlength of rod 1 greater than, less than, or equal to the change inlength of rod 2?

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Rotational Dynamics

Section: Chapter Questions

Problem 8WUE: A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and...

See similar textbooks

Similar questions

A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and a second 1.00 m from the right end. Find the magnitude of the force exerted on the plank by the second pivot. (See Section 8.4.)
A spade is modelled as a uniform rod, of mass 2kg and length 90cm, attached to a uniform square lamina, of side 20cm and mass 0.5kg. A gardener holds the spade horizontally with hands 30cm and 60cm from the end of the rod. Find the vertical forces exerted by the gardener's hands. Im stuck on this q, pls help.
overhead view of a rigid rod that turnsabout a vertical axle until the identical rubber stoppers A and B are forced against rigid walls at distances rA = 7.0 cm and rB = 4.0 cmfrom the axle. Initially the stoppers touch the walls without beingcompressed.Then force of magnitude 220 N is applied perpendicularto the rod at a distance R = 5.0 cm from the axle.Find the magnitudeof the force compressing (a) stopper Aand (b) stopper B.
A uniform rod has mass m and length L. One end of the rod is attached to a fixed point O by a hinge and an additional force F is applied to the other end of the rod in the direction shown, perpendicular to the rod. Given that the rod is in mechanical equilibrium, what is the magnitude of the applied force F, expressed as a numerical multiple of mg, where g is the magnitude of the acceleration due to gravity? Express your answer as a decimal number, specified to 3 significant figures
A rigid vertical rod of mass 75 kg and length 4.0 m is connected to the floor by a bolt through its lower end A. The rod also has a wire connected between its top end B and the floor as shown in the figure. A horizontal force F = 500 N is applied at the midpoint of the rod. What is the tension in the wire?
A uniform horizontal beam 5.00 m long and weighting 3.03 102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05 102 N stands 1.60 m from the wall, find the magnitude of the tension in the cable and the force exerted by the wall on the beam. T = N Rx = N Ry = N Even if we selected some other axis for the torque equation, the solution would be the same. For example, if the axis were to pass through the center of gravity of the beam, the torque equation would involve both T and Ry. Together with Equations (1) and (2), however, the unknowns could still be found—a good exercise. In this example, notice the steps of the Problem-Solving Strategy could be carried out in the explicit recommended order.QUESTION What happens to the tension in the cable if the man in Figure (a) moves farther away from the wall? The tension would…
The drawing shows a rectangular peice of wood. The forces applied to corners B and D have the same magnitude of 14 N and are directed parallel to the tlong and short sides of the rectangle. The long side of the rectangle is twice as long as the short side. An axis of rotation is shown perpendicular to the place of the rectangle at its center. A third force (not shown in the drawing) is applied to corner A, directed along the short side of the rectangle (either toward B or away from B), such that the piece of wood is at equillibrium. Find the magnitude and direction of the force applied to corner A.
a uniform beam with a weight of 60 N and a length of 3.2 m is hinged at its lower end, and a horizontal force of magnitude 50 N acts at its upper end.The beam is held vertical by a cable that makes angle u = 25° with the ground and is attached to the beam at height h = 2.0 m. What are (a) the tension in the cable and (b) the force on the beam from the hinge in unit-vector notation?
As shown in the figure below, a stick of length L = 0.410 m and mass m = 0.180 kg is in contact with a rough floor at one end and a frictionless bowling ball (diameter d = 20.00 cm) at some other point such that the angle between the stick and the floor is ? = 30°.Determine the following. (a) magnitude of the force exerted on the stick by the bowling ball N(b) horizontal component of the force exerted on the stick by the floor N(c) vertical component of the force exerted on the stick by the floor N
Three electrical charges isolated from the rest of the universe are located at the vertices of an equilateral triangle. Charge 3 attracts charge 1 with a force of modulus F1(3) = 4.3 N and repels charge 2 with a force of modulus F2(3) = 6.7 N. What is the modulus of the sum of the reaction forces on the charge 3 in Newtons? a. 10,95 b. 8,45 c. 9,60 d. None of the other alternatives are correct. e. 12,39 f. 2,21 g. 15,17 h. 0,86
As shown in the figure below, a stick of length L = 0.425 m and mass m = 0.225 kg is in contact with a rough floor at one end and a frictionless bowling ball (diameter d = 16.00 cm) at some other point such that the angle between the stick and the floor is ? = 30°. Determine the following. (a) magnitude of the force exerted on the stick by the bowling ballN(b) horizontal component of the force exerted on the stick by the floorN(c) vertical component of the force exerted on the stick by the floorN
a uniform sphere of mass m = 1.99 kg and radius r = 0.314 m is held in place by a massless rope attached to a frictionless wall a distance L = 1.87 m above the center of the sphere. Find (a) the tension in the rope and (b) the force on the sphere from the wall.