A hollow hexagonal prism, side of base 30 mm and axis 60 mm long, has a square hole of side 20 mm through it such that the axis of the hole coincides with that of the prism. The prism rests with its base on HPand one of its rectangular faces is perpendicular to VP. It is cut by a plane perpendicular to VP, inclined at 45 to HP and passing through a point on the axis at a distance of 20 mm from its top end. Draw the sectional top view and the true shape of the section

A hollow hexagonal prism, side of base 30 mm and axis 60 mm long, has a square hole of side 20 mm through it such that the axis of the hole coincides with that of the prism. The prism rests with its base on HPand one of its rectangular faces is perpendicular to VP. It is cut by a plane perpendicular to VP, inclined at 45 to HP and passing through a point on the axis at a distance of 20 mm from its top end. Draw the sectional top view and the true shape of the section

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.86RP: The flanged bolt coupling is fabricated by drilling 10 evenly spaced 0.5-in. diameter bolt holes in...

See similar textbooks

Similar questions

Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
The flanged bolt coupling is fabricated by drilling 10 evenly spaced 0.5-in. diameter bolt holes in a steel plate. The radii of the plate and bolt circle are 5 in. and 4 in., respectively. Determine the percent reduction in the polar moment of the area about point O due to the drilling operation.
A W867 section is joined to a C1020 section to form a structural member that has the cross section shown. Calculate Ix and Iy for this cross section. (See Probs. 9.13 and 9.16 for the properties of the structural sections.)
Determine Iu for the inverted T-section shown. Note that the section is symmetric about the y-axis.
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
4 A frustum of a cone 72 mm diameter of circular base, 48 mm diameter of top and having anaxis of 72 mm length has a hole of 30 mm diameter drilled centrally through its flat faces.The frustum rests on the rim of its base in such a way that the base makes an angle of 45° toHP and the axis is in a vertical plane parallel to VP. Draw its elevation and plan
A triangular prism of base side 45 mm and length of axis 75 mm has its edge of base on the HP and inclined at 50° to the VP. The face through that edge makes an angle of 30° to the HP. Draw the projection of the prism. A pentagonal prism of side of base 35 mm and length of axis 70 mm has a side of base parallel to the HP. The axis of the prism is inclined at 30° to the HP and 45° to the VP. Draw the projections of the prism.
A pentagonal prism of side of base 35 mm and length of axis 70 mm has a side of base parallel to the HP. The axis of the prism is inclined at 30° to the HP and 45° to the VP. Draw the projections of the prism.
A right circular cylinder, 40 mm base diameter and 65 mm height is held such that its axis isinclined to the HP at 300. It is cut by a plane inclined at 45° to the HP and passing throughthe axis at a point 25 mm away from the base. Draw a sectional plan and elevation of thecylinder and show the true shape of the section.
Calculate the second moment of area for 36 cm diameter shaft in in4 about the x-x axis
Find Ix and Iy for the L-shaped cross-section shown.
8.5 Determine I, for the thin-walled sections shown in Figures 8.9(a) to 8.9(c), where the wall thicknesses are 0.01 m. NB Dimensions are in metres. second moment of area about a horizontal axis passing through the centroid.