A pole is supported by a wire which exerts a pull of 200 lb on top of the pole. If the angle between the wire ang the pole is 50°, what are the horizontal and vertical components of the pull on the pole?

A pole is supported by a wire which exerts a pull of 200 lb on top of the pole. If the angle between the wire ang the pole is 50°, what are the horizontal and vertical components of the pull on the pole?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Related questions

Q: Given data: Q=3.3 m3/s A=4 m2 Find velocity

A: Given data : Discharge=Q Area=A To find : Velocity

Q: A heating device contains 5 kg water and is being heated. During the process, 11 kJ/kg of heat is tr...

Q: A certain hospital has 415 patients; 76 have high blood pressure only, 123 have heart problems only,...

Q: An air stream with a Mach number of (3.04) a pressure of (302 kPa) and a temperature of (502 K) ente...

Q: What is the internal energy of 5kg of superheated R-134A at -152C and 0.5 MPa? O1.305 kJ/kg/K O 34.1...

Q: Homework F 52KN ) The slope of the 5.2-kN force F is specified as shown in the figure. Express F as ...

Q: MABP is a straight line and the following observations were made. Angle DAM 70° 19' 00" Angle CBP 56...

Q: Two smooth billiard balls A and B each have a mass of 200 g. A strikes B with a velocity (va)1 = 1.2...

A: Answer: The magnitude of final velocity of A just after collision is 0.640 m/s.

Q: Find the required diameter of a droplet of water in order to have a pressure of 1 kPa within it, rel...

Q: • A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, an...

Q: The power required to drive the compressor in Carnot refrigeration is 50 Hp. It operates between -5°...

A: GivenCarnot refrigeration systempower required to compressor W=50HPT1=-5oC=268KT2=40oC=313K

Q: A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high the entire m...

Q: A belt driven compressor is used in a refrigeration system that will cool 10 li/sec of water from 13...

A: Please apply the concept of refrigerator to solve this problem

Q: QI: The cable AB supports three vertical loads as shown in next figure. Compute the resultant of the...

A: A cable with three downward forces is provided. Find the resultant of these forces, as well as its l...

Q: A 15-cm nickel cube is fixed at its base. A force of 1.44x109 dynes is applied parallel to its upper...

Q: calculate the density viscosity thermal conductivity and specific heat of water at 40 degrees celsiu...

A: Quantity Value Unit Density 995 kg/m3 Dynamic Viscosity 6.5372 x 10-4 Pa-s Kinematic Viscosity...

Q: Problem 2 Hinge A stop-block on the edge of the gate at B will break whenever the force reaches 40KN...

Q: fferent parts of the brakes system of an off-road bicycle

A: introduction In the marine and seaward industry, plan and hardware setups fluctuate from one framew...

Q: Given the problem: In the frame, shown, members 'ACE' and 'BCD' are connected by a pin at 'C' and b...

A: Given: External Force on element BCD=446 N The free body diagram of the given frame is as shown bel...

Q: A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a man...

A: Answer: The amount of water circulated through the pump is 0.40446 m3/s.

Q: . Air enters a counter flow HE at 70°C and leaves at 40°C. Water enters at 30°C and leaves at 50°C, ...

A: Given, Inlet temperature of hot fluid = Th1 = 70 oC Outlet temperature of hot fluid = Th2 = 40 oC In...

Q: 1. The spur gears shown in Figure 1 have a diametral pitch of 2 teeth per inch and a 20° - press ar ...

Q: 13 A uniform flow with a velocity of 3m/s is superimposed on the plane source of strength 20 m³/s. T...

Q: Develop the expression to determine: the elevation of the oil-water surface (Yi) and the pressure gr...

A: The course through permeable limits is critical both in mechanical as well as biophysical streams. M...

Q: 3.4 Consider a steady, incompressible, 2D velocity field for motion parallel to the x-axis with cons...

A: Given: The shear rate , dudy=Ay

Q: 4. A reversed Carnot cycle is used for refrigeration and rejects 1000kW of heat at 67C while receivi...

Q: A heat pump supplies heat energy to a house in order to maintain its temperature at 20°C. Over a per...

Q: The water flow (T: with a diameter of D = 0.2 m has a head loss due to friction of hp 20°C) in an as...

A: Answer: The volumetric flow rate of water through this pipe is 19.574 litre/sec.

Q: Which of the following is true? A. csc(-θ)=cscθ B. tan(-θ)=tanθ C. sin(-θ)=sinθ D.cos(-θ)=cosθ

A: Option D is correct Cos (-θ) = Cos θ Where sin (-θ) = - sin θ Tan θ=sinθcosθ Therefore , Tan(- θ)= -...

Q: Begin a full-size layout of a pair of spur gears having a 4:1 velocity ratio, a 10-in center distanc...

Q: Part A Member CB has a square cross section of 30 mm on each side. (Eigure.1) Determine the largest ...

Q: he elevator starts from rest at the first floor of the building. It can accelerate at 5 ft/sec2 and ...

Q: 3.13 A uniform flow with a velocity of 3m/s is superimposed on the plane source of strength 20m'/s. ...

Q: compute the tensile strength and ductility of a cylindrical copper rod if it is cold worked such tha...

Q: Two blocks respectively A weighs 1600N and B weighs 2400N are connected by a spring both rests on an...

A: Let's first draw the diagram of our problem:

Q: 3.13 A uniform flow with a velocity of 3 m/s is superimposed on the plane source of strength 20 m³/s...

Q: Problem (5.4) A nozzle in an impulse turbine delivers 1 kg/s steam to a set of blades moving at 200 ...

Q: Figure shows a hydraulic elevator which capable to carry 450 kg of passengers from the ground to the...

A: Since we only answer up to 3 subparts so we will answer the first 3. Please resubmit the question by...

Q: What is the hardest metal? What is it's Vicker's Hardness score?

Q: Q1 /Draw S.F.D and B.M.D 50 KN/m 20 kN/m 100 Nm 3m 6m Gm 3m Shear Force Diagram

A: Given

Q: What are the molecular weight and enthalpy (in [kJ/kg]) of a gas at P= 1500 [kPa] and T= 727 [°C], i...

A: Write the expression of molecular weight of the mixture of gas. W=n1W1+n2W2+n3W3+n4W4+n5W5n1+n2+n3+n...

Q: Dimension of a centrifugal pump impeller are Parameter Inlet, Section 1 Outlet, Section 2 Radius,r (...

Q: A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B as shown. Th...

Q: 1) Particle Motion and Coordinate Systems y y = 0.001x² %3D 100 m The jet pictured above is followin...

Q: (Problem 1) A Rankine Regenerative steam power cycles employs two stage of steam extraction at press...

Q: In a steam plant 100 kg/min of dry-saturated steam at 30 bar enters the turbine. After expanding ise...

Q: am is flowing through an adiabatic throttling valve (no heat loss or external work). Steam enters po...

A: Given:At state 1, P1=689 kPa absoluteT1=171.1o CP2=359 kPa

Q: Why is there a laser beam shooting out of the front of this telescope (in the inset picture)?

A: Given Telescope To find Laser beam shooting out of telescope

Q: ly using polygon method the resultant of th e. Solve also for the corresponding equilibrium table, p...

A: Hi and thank you for the questions. Since you have asked multiple questions, we will solve the first...

Q: The engine of the helicopter is delivering 600 hp to the rotor shaft when the blade is rotating at 1...

A: The radius are calculated for both the conditions and bigger radius is considered for final selectio...

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the internal force systems acting on sections 1 and 2.
The structure is supported by a pin at C and a cable attached to A. The cable runs over the small pulley D. Find the internal force systems acting on sections 1 and 2.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
Show that all diagonal members of the truss carry the same force, and find the magnitude of this force.
The 15-m-long cable supports the loads W1 and W2 as shown. Find the ratio W1/W2 for which the segment BC will be horizontal; that is, 2=0.
The tongs shown are designed for lifting blocks of ice. If the weight of the ice block is W, find the horizontal force between the tongs and the ice block at C and D. Neglect the weights of the tongs.
A boat is being towed through a canal by a horizontal cable which makes an angle of 10° with the shore. If the force tending to move the boat along the canal is 197N, find the pull on the cable?
A force of 30 N is applied to the input piston of a hydraulic jack. If the input and output piston have areas of 0.2 m² and 0.8 m², respectively, what is the minimum weight that can be lifted by the jack?
To move a heavy crate across a floor, one end of a rope is tied to it and the other end is tied to a wall 30 ft away. When a force of 100 lb is applied to the midpoint of the rope, the rope stretches so that the midpoint moves to the side by 2 ft. What is the force on the crate? Select the correct response: 400 lb 500 lb 410 lb 379 lb
The small piston of a hydraulic press has a cross-sectional area of 3cm2, and its larger piston has a cross-sectional area of 200cm2. What downward force must be applied to the small piston for the lift to raise a load of 15KN?