Answered: A hollow shaft has an inner diameter of…

A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torque if the shear stress is not to exceed 120 MPa in N-m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Related questions

Q: fınd a vector of length 5 unit that makes angle 76° with Y-axis and 25° with Z-axis ?

A: Given that, Length of the vector, l=5 unit,Angle of length with Y-axis, β=76°Angle of length with Z-...

Q: Q2. A hydraulically actuated horizontal slider mechanism is illustrated in figure 2 where the motion...

A: Hydraulical horizontal slider mechanism is a mechanism which is actuated with the help of hydraulic ...

Q: 1. Suppose that a car at rest begins accelerating at a constant rate of 15ft/sec2. (a) Determine how...

A: It is very basic question of mechanics. Topic motion under constant acceleration. Used concept is eq...

Q: Please upload the excel to support your results on how to find the inertia force of reciprocating as...

Q: R R d centroid centroid R -T/3 n: Centroid at origin 3 Sectors: Centroid at (0, 1.732R/n

A: To given thatr=3x2+y2=r2x2+y2=33

Q: The system in the figure below is at 20 °C. If the pressure at point A is 2900 lb/ft2, determine the...

A: To find pressure at point B,C,D

Q: A model rocket is launched from a point A with an initial velocity, vo of 85 m/s. If the rocket's de...

Q: required width (bmin) if the allowable bending stress in the material is 16 MPa? If the beam shown i...

Q: Decoding a Message The cryptogram below was encoded with a 2 x 2 matrix. The last word of the messag...

Q: for distance s= 54 - 17t from time 0.1 to 2 seconds, determine the maximum velocity.

Q: The gas 3. A stationary power plant operating on ideal Brayton cycle has pressure ratio of temperatu...

Q: The refrigeration system has a flow rate of 0.45 kg/s with a suction pressure of 112 kPa and the dis...

Q: 2 kips 4 kips 4 kips Determine the force in members FH, EH, and 4 kips EG using method of sections a...

Q: 1. A building exhaust fan for a large commercial bullding weighs 180 pounds and operates at a speed ...

A: Given: weight of the exhaust fan→m=180 lbs Speed of the fan→N=600 rpm Hence rotational speed of the ...

Q: SOLVE! A *(dot) B X C A. 5i - 3j + 4k B. -6i + 13j + 7k C. 10i + 14j + 7k

Q: Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure b...

Q: What is the definition of Routine Violence in Aviation Safety Regulations and give some of its examp...

Q: The pressure in the tank is 50 psi. Find the equivalent pressure head of water. Find the...

Q: Describe the steps involved in the preparation of a metallographic sample: > Sectioning (cutting) > ...

Q: A R-134A vapor refrigeration cycle operates at an evaporator temperature of -17 °C and a condensing ...

A: (a) for an ideal saturation cycle

Q: Air enters the compressor of an ideal gas refrigeration cycle at -23°C and enters the turbine at 17°...

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete reve...

A: Given Load, P = 5000 lbs =2268 kg Thickness, t = 0.5 in ...

Q: Why is correct dimensioning of engineering drawings important? Use suitable examples in your explana...

A: To find:- Imprtance of dimensioning in engineering drawing with example.

Q: A mechanical system is shown in the Figure below, which is subjected to a known displacement x3(t) w...

A: The mechanical system is subjected to a known displacement x3(t).

Q: The velocities of the particles at an instant are VA = 6m/s and VB= 8m/s, with the angle between the...

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid ...

Q: b. Consider the following system, where you are applying a load P: cg cg Mathematically, show which ...

A: Solution: (a) Given Data: b = 5 h = 7 d = 2

Q: Problem Set – Temperature Change 1. A steel tire has a dimensions indicated in the figure below. At ...

A: Given : T1 = 78 C T2 = 24 Cα=12.3 μm/CE=100 Gpa To find : Contact pressure

Q: -3 m end is tied to a steel cable of length 3.00 m, as shown in the figure. The other end of the cab...

Q: If the beam shown in the Fig. has a square cross section, what is their minimum required width (bmin...

Q: FORWARD KINEMATICS RR ROBOT X2 = x,+ L2 cos (0) (x2. Y2) Ja-e L2 Y2 = Y + L, sin (0) (x1. y1) x = x,...

A: In the given question, Position of joint 1 = ( x1 , y1 ) Joint-1 variable = θ Position of joint 2 = ...

Q: R2 R e+Vcc R Kin W •Vout -Vec C Vout R R Comparator Hysteresis. Opamp Circuit In which way are the t...

A: The comparator is an electronic decision making circuit that makes use of an operational amplifiers ...

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete reve...

A: Given Load, P = 5000 lbs =2268 kg Thickness, t = 0.5 in ...

Q: A Carnot vapor refrigeration cycle operates between thermal reservoirs at 40 ⁰F and 100 ⁰F. Determin...

A: Given data: TL=40°F=277.594 KTH=100°F=310.928 K Need to determine the coefficient of performance.

Q: 6. Find the reaction forces at point A and B 20 lb 30 lb/ft A B 10' 10'

Q: A small ship capable of making a speed of 5.8 knots through still water maintains a heading due east...

A: Answer: (a) The speed of the current is 1.6175 knots. (b) It's direction measured clockwise from Nor...

Q: 05) Find the minimum volume of the truss shown with constraints on the depth of the truss (v), cross...

Q: Q: What is the difference between addition polymerization and condensation polymerization? In additi...

Q: A heat exchanger is incorporated into an ideal air-standard refrigeration cycle, as shown in figure....

Q: 2 kg of air, which can be modeled as an ideal gas, undergoes an isothermal process from 1.3bar and 2...

A: Find the heat transfer and entropy produced.

Q: find the stresses on the plane Mhor Circle anod locate Op and draw 100 50 15 B

A: Identifying angles and drawing Mohr circle:

Q: A pipe network consists of pipeline as shown. If the total rate of flow is 10 liters/sec, compute th...

A: Given: Flow rate of water→Q=10 lit/sec=0.01 m3s Summision of Flow rate of water in pipe 2 and pipe 3...

Q: In one sentence, explain the difference between straightness and flatness.

Q: It is desired to determine the cost of the submerged arc welding operation in the preceding problem,...

Q: The velocity of a particle travelling along a straight line is v = (3t^2 - 6t) ft/s, where t is in s...

A: Given data as per question v = (3t^2 - 6t) ft/s Calculations The Position of particle can be determi...

Q: What are dislocations? One dimensional crystal defects. Bone ruptures. Places in the crystal wher...

A: It is required to determine correct option

Q: Oil is to flow through a pipe at 80°C, and for experimental purposes, the oil flow must be hydrodyna...

Q: Q1// A heat engine operates between a source at 550°C and a sink at 25°C. If heat is supplied to the...

Q: Calculate the mechanical advantage of the 30'

A: Given :- To find mechanical adavantage.

Q: Q5// A Carnot refrigerator operates in a room in which the temperature is 25°C. The refrigerator con...

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torque
if the shear stress is not to exceed
120 MPa in N-m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A torque T is applied to a thin-walled tube having a cross section in the shape of a regular hexagon with constant wall thickness t and side length b (see figure). Obtain formulas for the shear stress rand the rate of twist
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).